Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Joystick hookup on a JD 4430 for Glen A Terry


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by JD Seller on December 16, 2013 at 19:39:01 from (208.126.196.144):

Here is how I hooked up a joystick on a JD 4430 I mounted a JD 740 loader on last year. This is plumbed in direct without using a power beyond block.

Here is the actual valve mounted to the bottom of the right hand battery box. The box is already drilled to do this. Just used carriage bolts down from the top.

third party image

Here is the supply line/hose. The Tee fitting is hooked directly to the pressure control valve. The line coming out and curing to the right is the supply to the valve. The line going off the back and up replaces the steel supply line to the SCVs and three point.

third party image

Here you can see the joystick control mounts so the joystick lever missed the shifter levers.

third party image

This is the cables coming up through the floor of the cab. There is a knock out plug on most of the newer cabs. If there is not one I just take a smaller hole saw and saw two holes that over lap for the grommet to fit around the cables.

third party image

Here is the return line. I just drill and tap a 3/4-10 hole in the filter cover. I then take a round file and put a chamfer around the out side of the hole. The install a JIC oring fitting. You can used the factory drilled return filter cover but they are not cheap. I route the hose up and over the transmission this way there is nothing hanging down under the belly to get caught.

I know you can dump back into the sump through the rock shaft housing. I just like dumping back in right at the filter. Plus on the older tractors doing it this way will make the loader operate faster and smoother.

third party image


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy