Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: John Deere 2640


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by JD Seller on April 11, 2013 at 23:02:25 from (208.126.196.144):

In Reply to: John Deere 2640 posted by KSpring on April 10, 2013 at 14:18:58:

QUIT throwing money at the tractor and figure out the problem first!!!!!!

1) Drain all the hydraulic oil and remove the sump screen and see if it is full of junk. If it has lots of fiber looking stuff in it then the rear brakes are bad and they need repaired and then the whole tractor needs to have the hydraulics cleaned out if it was ran long this way. If the screen and oil look good then go to step two.

2) TX Jim had a good thing to look at that costs zero money. Start the tractor and raise the three point. Look through the filler cap toward the front of the tractor, for spraying hydraulic oil. The Mannheim tractors have plugs that are held in with snap rings, that cover where they machine the control vale bores. These plugs wiggle back and forth a little when the valves work. This wiggle eats up the orings on the plugs and then you have a high pressure internal leak. I bet that I have fixed a hundred of them.

3) Pull the gear shift housing off. ( Do not start the tractor with this off unless you like cleaning oil off the ceiling) Put it in park first and then just remove the bolts and lift it straight up. This will allow you to check the Independent PTO lines as they stick into the bottom of the gear shifter housing. The control valve is located between the gear shifters in the cover. These lines are a common thing to break. They vibrate and crack. When they do this the dump the charge/transmission pump oil right back to the sump and starve the main pump. Also look down into the housing and see if the charge pump lines are installed correctly.

4)When the tractor has been run long enough to warm the hydraulic oil up, Does the back side of the steering column feel hot to the touch??? I mean the casting about 6-8 inch under the steering wheel. This is where the steering control valves are at. They can cause the whole system to not work correctly. The real problem if you have an issue with the steering valve is that about 75% of the JD mechanics do not know how repair/rebuild these steering units correctly. Then to make it even better, since it an older tractor, most dealers will put the newest guy on it while the top mechanics work on the newer high dollar stuff. I know one guy that had $5000 dollars tied up in getting his steering valve to work correctly. This included buying several valves that had been rebuilt and where not good.

These are something to check. I do not remember the old post so listing the number of thing I said to do does not help me know what you have already done. Post use a short description of what you have checked so far. Also without two pressure gauges and a some fittings you really can't check the system out very much. These tractors have complicated hydraulic system that requires everything to work together or they will not work correctly.

I had a JD 2640 that I owned for 3 years. It had a loader on it before I got the tractor. The main hydraulic pump had gone bad. They just replaced the main pump. So the junk was still in all the rest of the system. In the first two years I had every single hydraulic component off and had to clean/repair it. Once I got everything working I shipped the tractor down the road. Once they have had a major hydraulic system failure they need to be completely cleaned out the first time so that nothing else is ruined. If they are run with the bad parts long the whole system is a problem after that.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - A Farmall Story - by Ed Meadors. The year was 1978. Our young family had recently moved to rural Chesapeake, Virginia to a plot of land which would finally allow us to realize our dreams of a huge garden, critters and more lawn and pasture than we would ever use! We needed a TRACTOR; not a riding mower or tractor wannabe, but a real TRACTOR. The answer to our needs materialized in the form of a '44 Farmall A, complete with cultivators, discs, single plow, a 5ft.Woods belly mower and one, mounted spare 9.00x24 rear wheel. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy