The standard tankless heaters do not heat water to any given temp. They only work by temp-rise. The standard 120 F thermostat setting has nothing to do with how hot the water is actually heated.
If you've got 45 F degree well water (like all my houses have)- that Rheem will only raise the temp of the water by 20 F at full capacity (2.5 GPM). That means - if you've got cold well water - your "hot" water will be 65 degrees F instead of 45 F. If you only run your water at 1 gallon per minute, you get a 40 F rise. Much better for small usage and worthless for high flow (like taking a shower?).
What the heck is happening to your old failed heaters? I rarely buy new. I buy used - usually $50 for gas or electric and I've rarely ever had one go bad. I did have to fix a few with minor issues. I've got four houses - all with used tank heaters and some have been in use for 30 years.
Note also that standard tankless heaters do not work with preheated water. If you heat your water in the summer with solar, or in the winter with a wood fire - standard tankless heaters can't be used. There are special and more expensive models made for that.
A well insulated tank heater is just as efficient as a tankless - and cheaper - and it actually keeps hot water on hand.
Rheem RTE 7 Indoor Series Electric Water Heater Required Breaker – 30, 240 volts Maximum Flow Rate - 2.5 GPM Heats with 20 F rise at 2.5 GPM, 40F rise at 1.2 GPM, 90F at .5 GPM
Rinnai Model Number REU-VB2020FFU-US 15,000 - 150,000 Btu/h (Natural Gas and Propane) Hot Water Capacity 0.6 to 5.3 GPM Gas supply: 3/4 inch MNPT Cold water inlet: 3/4 inch MNPT Hot water outlet: 3/4 inch MNPT Efficiency 82% Temperature rise at 5.3 GPM is 40 degrees F, 125 F at 2 GPM
Rinnai Model Number REU-VB2528FFUD-US Hot Water Capacity 0.4 to 7.5 GPM (40° F rise) Propane: 82% Residential: 98°F - 140°F 10,300 - 180,000 BTU/h (Propane) Gas supply: 3/4 inch MNPT Cold water inlet: 3/4 inch MNPT Hot water outlet: 3/4 inch MNPT
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
