Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
John Deere Tractors Discussion Board

Re: Re: Re: Get my Tractor to start!


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Clooney on November 21, 2002 at 07:45:26 from (172.153.216.143):

In Reply to: Re: Re: Get my Tractor to start! posted by Justin on November 21, 2002 at 07:20:13:

Justin, do an initial setting on the carb; set the idle screw [farthest from the center of the tractor] to 2 turns out from seated & set the load screw [closest to the center of the tractor] to 1 turn out from seated. If the carb is good that should be pretty close for a good hand start.
~I presume you have a DLTX 26 or 46 on it? If so make sure the choke plate has the spring loaded trap door in it & it is closing, & opens toward the inside of the carb, those things have a habit of being missing.
~Try different choke & throttle settings; My H's start best at 1/4 or less throttle [actually throttle plate lever just off the stop pin] & full choke for 1-2 turns, then 7/8 choke for the next turn, then 1/2 for the next [if needed], then if no start try wide open throttle & no coke, if it barks there go back to 3/4 coke & 1/2 throttle.
~Do a cold compression check, & if below 60-65 or so try some 2-cycle oil in the gas to help seal the rings at cranking speeds.
~If you live in a cold climate, get rid of your summer gas & put in winter gas [don't laugh there is a difference].
~I have found on mine that opening the plug gap to .040" helps the starting as well as advancing the timing to 1/2" before L/H impulse lines up with case mark.
~If you are using 388 spark plugs, in cold whether try Champion D-23 with 2 plug gaskets under each plug. I have found they start better when it's real cold. In warmer whether it doesn't seem to make any difference on the plug make.
~In real cold whether try opening the idle needle 1/2 turn more [just for starting].
~When stopping the tractor, run it out of fuel, don't choke it or stall it.


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Re: Get my Tractor to start!

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums  |  Order Support


Today's Featured Article - Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens ... [Read Article]

Latest Ad: 65 Massey FERGUSON DIESEL [More Ads]

Copyright © 1997-2026 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy