|
John Deere Tractors Discussion Board |
Re: removing back wheel disk
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Gerald J. on May 29, 2005 at 19:40:13 from (67.0.108.254):
In Reply to: removing back wheel disk posted by frank in PDL on May 29, 2005 at 16:20:24:
Like any JD cast wheel, it can be a pain. The official method is to loosen the three bolts from the outside holding the wedge and tighten the two jack bolts to push the wedge loose. Unless that's been done regularly nothing is going to move. The official JD wrenches for that were close to 2 feet long so they do expect quit a bit of torque will be applied. When I did that to my 4020 a few years back, I used a 6 foot pipe on my 3/4 drive breaker bar and had to use hearing protection because the jack bolts screamed. When that doesn't work the next official method is to bounce a 20 pound post maul against the outer end off the axle, HARD. Then put some more torque on the jack screws. There is benefit of using a really good penetrating oil, like Kroil or PB Blaster (everything else is useless) all over that wedge inside and out. Some have made a wedge pusher out of pipe cut so it only pushes on the wedge to be moved (not the one with the gear). The pipe has to be long enough to extend past the end of the axle with a cap welded on the end of the pipe. Then the post maul hits that pipe. A few (and you should find dozens of posts on the topic with a search on wheel wedge removal on this page) have reported breaking the wedge with the jack screws or of having to apply a great deal of heat to the wheel. Some have suggested leaving the wedge bolts a bit loose and driving the tractor to break the rust loose. A few have rigged hydraulic jacks on the end of the axle with sturdy chains to the wheel and broken it loose that way, though I could see breaking the wheel that way too. Gerald J.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Field Modifications (Sins of the Farmer) - by Staff. Picture a new Chevrolet driving down the street without it's grill, right fender and trunk lid. Imagine a crude hole made in the hood to accommodate a new taller air cleaner, the fender wells cut away to make way for larger tires, and half of a sliding glass door used to replace the windshield. Top that off with an old set of '36 Ford headlight shells bolted to the hood. Pretty unlikely for a car... but for a tractor, this is pretty normal. It seems that more often than not they a
... [Read Article]
Latest Ad:
John Deere 750 Diesel Yanmar J80TU engine. pistons and rings replaced when discovered crankshaft was bent. 3995 OBO Pictures available upon request
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|