|
Farmall & IHC Tractors Discussion Board |
Re: 56/57 International 350 Diesal Utility
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by dick on January 04, 2001 at 18:54:25 from (199.239.12.58):
In Reply to: 56/57 International 350 Diesal Utility posted by Hilltopper on January 04, 2001 at 17:11:04:
The 350 Utility replaced the 300 Utility late in 1956 and was made through 1958. There is not much difference between the gas tractors except the 350 had a two-tone paint job, and its Fast Hitch (assuming the tractor had it) may have draft control. The 350U was also offered with a diesel engine, in a Wheatlands version, and a high-clearance version. I don't believe these were available in the 300U, but others can correct me on this. The diesel engine was made by Continental, and I have seen (somewhere on this forum, I think) an indication that parts for that engine are hard to get. I believe it's the same diesel engine that was used in the Farmall 350D. There weren't nearly as many 350Us made as 300Us, and the diesel was some subset of that number, so you are probably getting into the area of an "uncommon" tractor, but I doubt that it's a rare tractor. 45 Hp (max.) is about right for the PTO, drawbar would be slightly less. The 300U/350U tractors seem to be very popular with their owners (I like mine), with the standard complaint being that they're hard to steer without power steering. Really hasn't been too much functionality added to "small" tractors since these came out except ROPS. My opinion is that the Fast Hitch is an advantage, even when hooking up to three-point implements - much less pushing, shoving, and cursing involved once you learn how to do it. If you think the tractor would meet your needs, and the price is right, I'd say buy it.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Fabricating Sidesheets - by Chris Pratt. The easiest and best first-time project for wanna-be sheet-metal workers like myself is flat or nearly flat metal cut and drilled to be a tractor's sidesheet. A sidesheet is sheetmetal to cover either the engine as in the case of early Oliver's, Massey-Harris' and many crawlers or the wiring and electrical components as in the case of the Massey-Harris Pony, Allis Chalmers' D Series (D-14, D-15, D-12, D-10, D-17, and D-19). The need for fabricating becomes obvious when you go to buy any of these
... [Read Article]
Latest Ad:
For sale Farmall super A tractor is complete and has just been setting for awhile,it was running when pulled out of the barn,shouldn’t take to much to get it going asking 1100.00
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|