|
Farmall & IHC Tractors Discussion Board |
Re: What does a 1066 weigh
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Hugh MacKay on November 07, 2006 at 10:23:39 from (209.226.247.120):
In Reply to: What does a 1066 weigh posted by JPatton on November 06, 2006 at 21:39:28:
JPatton: I think I'd get a second opinion on that weight. My 1066 was gear drive, ROPS cab, air and duals, and on this particular ocasion if I remember correctly 6 97# front end weights. My memory is a bit rusty, actually I'd sooner forget, but I think it came in under 11,000#. This was a fiasco at highway scales on a holliday weekend with 3 tractors on 2 trucks. He made us unload and reload 3 times. I'm certain when we arrived the truck with lone 656 and able to legally haul 10,000# was legal. I knew I was overweight with 1066 and Deere 540A forestry skidder, We left there with 1066 on small truck and 656 and Deere on the trailer. In my opinion when we left there we were both over weight. I think his Thanksgiving work schedule had him in a bad mood. We were there 3 hours, should have had an official weight for each tractor and each truck. After all that weighing I had the 656 with cab pegged at just under 7,000# and the other two just under 11,000# each. I'm thinking he officially had up to 10% tolerance to play with. Both of us 10% over was better in his eyes than one truck legal and one 20% over. I know we could have put either 1066 or Deere on small truck and satisfied him. At least he didn't want money. Someone must have shipping weights on these, I know some of the heavy chassis 06, 56 and 66 series tractors came in under 10,000# without cabs.
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that�s wha
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|