|
Farmall & IHC Tractors Discussion Board |
Re: Need Some Advice on a Proper Plow
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Janicholson on July 25, 2006 at 12:56:18 from (199.17.6.122):
In Reply to: Need Some Advice on a Proper Plow posted by Mack in Tx on July 25, 2006 at 00:42:01:
Dear Mack, The reason we have not answered is we need to be sure what you mean. The word plow means several things: a moldboard turning plow with "bottoms", or a multi disk plow with cup shaped rolling cutters that flip the dirt over and are ganged similar to the mold board plow, or a chisel plow with multiple shanks that penetrate the ground (maybe 7-9")in a pattern and tear up the soil with direct action of the chisel points. Most other tillage equip. is a field cultivator, which is like a chisel plow but has sweeps on the shanks and usually is pulled shallower than a chisel plow, or a disk harrow. A disk Harrow has gangs of cup shaped disks arranged (usually) so that two gangs are in front throwing soil a bit outward, and two gangs in the rear throwing soil a bit inward. If a moldboard, it pulls what is called a 2-14plow If a Disk plow, 2-16" disks is all it will pull. If a chisel plow, it will do 5-6' (about 10 shanks) at modest depth. If a field cultivator, it will handle 6-7' of shanks at modest depth. If a disk harrow 8' is all it will want to pull. The opinions on the above info are for medium soils that have been tilled in the past. In sod, or heavy clay, they are optomistic. Others may have differing opinions, but I use Hs and now that were new when I was born in 1949. our soil is medium loam, and in some fields, blue/yellow clay. I hope this helps. JimN
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Two-Brush Generators - by Chris Pratt. Whether for product liability or because the aftermarket parts and labor business is lucrative, this concept is disturbingly prevalent. Fortunately when you step into your shop and make that jump 50 years back in time to work with your old tractor, this concept goes out the window. Even so, when it comes to the charging system, people quickly revert to this idea and start replacing the major components one at a time until it works. The reason you don't find any decals in your replacement set wit
... [Read Article]
Latest Ad:
WANTED IH C200 gas engine — complete running motor Wanted complete used IH C200 gas engine in running condition for an International 574 gas tractor. My block has a hole in it and is dead, so a rebuild kit wont do it — need a whole running motor. The C200 also came in the 544 and 674 gas trac
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|