|
Farmall & IHC Tractors Discussion Board |
Re: pto seal
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Paul in Mich on April 20, 2005 at 11:43:00 from (152.163.101.13):
In Reply to: pto seal posted by kirt vallot on April 19, 2005 at 19:30:06:
Kirt, Having read your post and the responses, including yours, I am inclined to think that you bought a PTO seal, but you really meant to replace the belt pulley shaft seal. These are two different seals. To replace the pulley spline shaft seal, you must remove the spline protective sleeve which is held in place by a retainer washer and bolt at the end of the spline. Then remove the seal retainer which is held by three cap screws. Remove the seal and press in a new one. The new ones differ from the originals in that the new seals are neoprene rather than leather, and are much thinner, (1/4 in approx) To install, make sure you apply some grease or patrolium jelly to the seal so that it will slide over the spline and onto the seal surface. Pounding these seals into the seal retainer invites disaster as it is very difficult to keep the seal straight and it is very easy to distort or trash the seal. Pressing works better, but either way, starting the seal straight is important. Unless the PTO shaft is leaking, I wouldnt think it would be necessary to replace it just for the sake of replacing it, as it is much more involved than replacing the pulley shaft seal. There is not a removable seal retainer for the PTO, and the original seal, because of its thickness is a bear to get out without removing the entire PTO assembly. Even with a seal puller, it is a difficult process. The new one is simpler to replace, simply because it is thinner. As some have said, it is possible to stack three replacement seals in place of the original PTO seal, but it really is not necessary, because of the composition of the newere seals. I hope this helps.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
My Ford Golden Jubilee - by Troy Estes. This article is about my '53 Ford Jubilee and a story that starts with taking the tractor to my brother's Starter/Alternator Rebuilding shop for a wiring fix. The generator was shot as well as all the wiring. I dropped off the tractor expecting a transformation from a 6 volt to a 12 volt system utilizing the original generator housing, and a total rewiring of the whole tractor. The front end center pin bushing was worn also so I ask that they replace it if they had time. Well, that�s wha
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|