|
Farmall & IHC Tractors Discussion Board |
Re: 2005 Gasoline Versus 1930's Gas
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Hugh MacKay on February 20, 2005 at 17:01:36 from (209.226.106.122):
In Reply to: Re: 2005 Gasoline Versus 1930's Gas posted by Bill in NC on February 20, 2005 at 16:10:46:
Bill: Really don't want to voice an opinion as to why. What I do see is tractor, truck, etc. not as productive as a comparable unit of 30 years ago. Some of these enviormental efficiency experts have a lot of one sided equasions. Kind of like the low water volume toilet, yes it takes 25% less water for a flush, but in most cases you must flush twice. Or the trucker on here the other night, he was told his new truck would give 1 mpg less than his 4 year old truck. Now if it's going to take more fuel, it will also require more oxygen to burn that extra fuel. I for one think we will run out of oxygen long before the emissions get us. I remember an accident number of years back, crew had a gasoline pump operating in a manhole. Pump was not operating very well so one guy went down to make it run better. He faltered much like the engine. A second guy went down to help the first guy. They both perished. Finding of the inquest stated that lack of oxygen, not monoxide was cause of death. Since the beginning of the industrial revolution we have reduced the oxygen content in our atmosphere from 40% down to roughly 18% in 2005. Only two things going to work, our engines suck in less oxygen and we grow more lushous green plants to replace the oxygen. I'd be willing to bet if our offset Farmalls were tuned up and sent off to Nebraska tests they would do just as well on todays fuel as they did all those many years ago.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens
... [Read Article]
Latest Ad:
WANTED Front grille/nose assembly for Massey Ferguson 1160 (also fits 1180 & 1190). Headlight-mount section. AGCO Grille 3706022M91 (supersedes 3705942M91), cover 3705494M1/M2, holders 3705501M91/3711158M92. New/NOS/good used OK. Jonesboro, AR - will pay shipping. Photo appreciated. Thanks
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|