|
Farmall & IHC Tractors Discussion Board |
Re: Hugh MacKay=== update on those plows
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by hugh MacKay on March 14, 2004 at 06:36:55 from (216.208.58.188):
In Reply to: Hugh MacKay=== update on those plows posted by rex simpkins on March 14, 2004 at 04:00:35:
Rex: One of the problems with plows and in particular these fast hitch plows, is I think they could all be ordered with small or large forks. Then you factor in 5 two furrow models; C-20, C-25, 209, 209A and 211. Add to that different widths of cut; 10", 11" and 12" used the same width bottom, some 14" and 16" were the same while others not. Then you add to that Ace, General Purpose, Plow Chief and Super Chief. Generally speaking I think you will find the C-20 and C-26 are from the 50s with 10", 11", 12" and 14" either Ace or General Purpose bottoms. Getting into the 60s are the 209, 209A and 211, 14" and 16", Plow Chief or Super Chief bottoms complete with trip beams. I think it would also be safe to say the majority of the C-20 and C-26 were small fork for SC, 200 and 230. The later 1960s plows were probably primarily large fork as the 240 tractor came with large sockets on hitch. The aforementioned plows were all two bottom. There were also C-30, C-36, 309, 309A and 311, being coresponding 3 furrow plows. Building plows was much like building a fence, you used necessary components to get the job done. If that doesn't confuse the issue enough, there were also on farm modifications. Sounds like you are into that. I have one candidate for that. I have an A-295 plow I converted to 1 point fast hitch. I have since acquired a 296 one point fast hitch plow. Both plows 2x12, with same mold boards, coulters, etc. I have offered the converted plow for sale couple of times, even gave 2 guys demonstrations. The plow does excellent work, but everyone believes I should sell it for $50. In actual fact I have probably $300. worth of plow bottom parts plus the fast hitch pull beam , I had fabricated at a cost of $85. That precise pull beam has many possibilities on fabrications I haven't even dreamed up yet.
Follow Ups:
Home
| Forums
Today's Featured Article -
The Day Mom Drove the 8N - by Brian Browning. My Dad was wanting to put in a garden but couldn't operate the 8N and handle the old horse drawn plow he had found and rigged up to use with the tractor. Well, he decided to go get Mom out of the house and have her drive the tractor while he walked behind the plow. You got to understand that while my Mom is a hard worker who will always help whenever she can... she had never operated farm machinery before that day. Dad got her out there, explained how the clutch was the same as in our o
... [Read Article]
Latest Ad:
18-32 Case Cross Motor
[More Ads]
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
