|
Farmall & IHC Tractors Discussion Board |
Re: Re: Re: Super C motor oil
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steve - IN on June 17, 2003 at 21:46:16 from (12.223.205.149):
In Reply to: Re: Re: Super C motor oil posted by Doug in OR on June 17, 2003 at 17:16:07:
Doug, I think we've had this discussion before -- maybe a year or two ago. I basically agree with you. I've used synthetics since ~1975 for some engines. On race engines, they run 20 to 30 degrees cooler on an oil temp gauge, and they do dyno slightly better. The amazing part is when you tear down an racing engine that's used synthetics from the get go and see the bearings -- they look like you just installed them. I use synthetics in 4 of my 5 tractors. The fifth one is the rub, I need to do a rebuild on it, and it would just burn off that nice expensive synthetic oil. So in the meantime, I'm using straight 30W and now 40W as it's gotten warm. You're absolutely right about cold starts -- but there is a trick known to lots of guys who went to flight school 30 or more years ago on piston engines. Leave the switch off - pull through the engine -- manually or with the starter, until oil pressure builds. Then go switch on. That mostly eliminates any cold start problem. If I use this engine when it's cold; then I'd use a 10w-40. 'Til then I get to turn it through then yell clear when I switch on. Guys who went to flight school less than 30 years ago quickly went into turbines and synthetics. There's nothing better for standing up to cold starts and also outrageous temps and revs. Next time this discussion comes up - maybe we should ask if someone would use 30W in an engine that turns >60,000 RPM at 20 below zero. If the answer is no - somebody has learned to appreciate synthetics.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Torque Wrenches - by Curtis Von Fange. When working with fasteners a torque wrench can play an important role in the correct assembly of critical equipment components. Lets examine in detail some of the reasons for using a torque wrench along with how to correctly use the variety of wrenches available. Applying the proper torque to a fastener accomplishes a number of tasks. First of all correct torque will hold the parts together. This may seem like a trite statement but � think about it for a second. Engineers have designed
... [Read Article]
Latest Ad:
WANTED IH C200 gas engine — complete running motor Wanted complete used IH C200 gas engine in running condition for an International 574 gas tractor. My block has a hole in it and is dead, so a rebuild kit wont do it — need a whole running motor. The C200 also came in the 544 and 674 gas trac
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|