|
Farmall & IHC Tractors Discussion Board |
Re: Re: Re: Painting Questions
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Steven@nd on June 09, 2002 at 12:40:53 from (12.15.56.102):
In Reply to: Re: Re: Painting Questions posted by K.B. on June 09, 2002 at 11:34:53:
Your local PPG paint supplier should be able to set you up with a mask for around $30 to $40. I think the last one I bought (replaceable filters) was around $40 or so. Be SURE to wear the mask at ALL times! I painted a little bit without one last summer and was sick for a month (no voice and sore throat). I paint inside our shop/storage shed. 1/2 of it has cement floor. In your case I would buy some cheap clear plastic or find old tarps to lay down on the floor to avoid kicking up dust. Humidity and temp will very much affect drying. You should not paint under 70 degrees F. There are different reducers that have different drying times for the varying temperatures. There is one for 70 and 85 degrees for sure and also one between those. I like using the 70 because the slower it dries the more shine you get, but this gives more time for bugs, dust, etc. I enjoy using our HVLP gun, however we did an excellent job with our $20 "touch up" gun on my 51 IH pickup. My advise is to buy some cheap (farm and fleet store) paint and thinner if you have never painted before and practice on old tin or cardboard to get the spray pattern set right. Once you are comfortable with the gun switch to the good stuff and test a little bit on scrap metal again. Always remember, if you mess up you can wait until it dries, sand it down and apply another coat. As for specific painting procedures, your local supplier should be able to help you out - mine gave me several sheets explaining what to do and what not to do. Very helpful to have. If I can find them I can scan them in and email them to you if you like. Feel free to email me if you have more questions. Steven
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Haying Before Tractors - by Owen Clark. Hi guys! At age 8 (1927, am now 79) I was learning how to drive a stacker team on the old homemade A-frame wooden stacker, on three of my uncles` dairy farms in Star Valley Wyoming (south of Jackson Hole, on the Wyoming-Idaho border). There was one steam tractor in the Valley, owned by an entrepeneur who used it to run his grain threshing machine, that he hauled from farm to farm for the fall harvest. We used teams of horses not only on the stacker, but on the buckrake to buck the dried
... [Read Article]
Latest Ad:
2555 Mahindra Shuttle 4x4 heat,air,diesel,7ft Mahindra heavy duty bushhog 7ft snowblade bucket
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|