|
Farmall & IHC Tractors Discussion Board |
Re: Farmall Super C rear end problem
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Harold Hubbard on May 01, 2007 at 04:28:57 from (66.6.176.23):
In Reply to: Re: Farmall Super C rear end problem posted by Ron F B on April 30, 2007 at 19:09:12:
This is a pretty common problem with the C super C, 200, and 230. I have a C and two Supers, and they have all been done at least once, and the C about three times. You don't have to work them all that heavily to break the axle, just a lot of hours. What got the C, I am sure was snowplowing and rough mowing. When doing either of these things, you are constantly shuttling back and forth, and each shift torques the axle a little bit, sort of like twisting a wire back and forth to break it. There are a lot of places that have used parts for sale, the axle is heavy enough that close is better to save on shipping. Many of the used ones will have had the outer end hacked off, this is perfectly okay, unless you need to set the wheels out to maximum width, or want show quality. There are two types of retainer for the bull gear, the early models use a plate with two bolts to hold it on, the later models are grooved for a retaining ring, make sure you get the hardware if the new axle is different than the old. While you have the axle out take a very close look at the bearings and seals, now is the time to replace them if necessary, just be sitting down when you ask the price. Now is the time to get a shop manual if you don't already have one. That and a parts book will answer many questions for you. If your interest runs that way, this might also be the time to start looking for a parts tractor. If you find one you can switch the whole axle and housing, and save yourself some work. beside that, if you are going to use the tractor you will eventually need other parts.
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Torque Wrenches - by Curtis Von Fange. When working with fasteners a torque wrench can play an important role in the correct assembly of critical equipment components. Lets examine in detail some of the reasons for using a torque wrench along with how to correctly use the variety of wrenches available. Applying the proper torque to a fastener accomplishes a number of tasks. First of all correct torque will hold the parts together. This may seem like a trite statement but � think about it for a second. Engineers have designed
... [Read Article]
Latest Ad:
WANTED IH C200 gas engine — complete running motor Wanted complete used IH C200 gas engine in running condition for an International 574 gas tractor. My block has a hole in it and is dead, so a rebuild kit wont do it — need a whole running motor. The C200 also came in the 544 and 674 gas trac
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|