|
Farmall & IHC Tractors Discussion Board |
W-6 hydralic,s?
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Kirk in ks, on February 23, 2007 at 18:48:08 from (65.166.184.45):
Last time I started the W-6<
It was ok, then after this parade i was in last summer, I accidently forgot to fill the hydralic tank, and when i was all done, ready to go home,
I went to start it, & drive it home,
and the thing would barely run,
I looked at the hyd pump?
and it was smoking hot, so i said ohh boy , i guess it was low on fluid,
so I parked it on side of road, left it there for two night,s,
went back to it to start it, and it ran ok with the fluid in it,
But i got a little closer to the House and it was leaking fluid underneath engine at the clutch
housing alot of fluid came out , so i shut it off, and i towed it home,
I didnt mess up the pump,
But,,,?
How did it get into the sump, and start to leak out the bottom where the clutch is?
I smelled the oil in the sump, and it smelled like hyd fluid, and was thin like water just like hyd fluid,
So,,,,,,?
Now, what do I do,
This thing was jury rigged for a loader and then the hyd tank lines were capped off,so the two line,s to the back from the front pump had no where to run to and just stopped,
I looked at the line,s, and they were alway,s vibrating and hot to the touch, and I have a feeling that the fluid had no where to go and just backed up pressure when it went to the back , & there wasnt any return line to the front
so it could run smooth in a circuit, around, and back to the front pump,
Could it have blown a seal in the clutch area and that,s why it started to leak when I was bringing it home?
I really need help on this as it is detrimental to tractor being redone the right way,
Replies:
Home
| Forums
| Order Support
Today's Featured Article -
Timing Your Magneto Ignition Tractor - by Chris Pratt. If you have done major engine work or restored your tractor, chances are you removed the magneto and spark plug wires and eventually reached the point where you had to put it all back together and make it run. On our first cosmetic restoration, not having a manual, we carefully marked the wires, taped the magneto in the position it came off, and were careful not to turn the engine over while we had these components off. We thought we could get by with this since the engine ran perfectly and would not need any internal work. After the cleanup and painting was done, we began reassembly and finally came to t
... [Read Article]
Latest Ad:
1965 International Harvester McCormick Farmall cub tractor 2,500. Two owner tractor. My grandfather bought new in 1966, then we inherited it. Have all the paperwork original manual and all maintenance records. It starts and moves. Comes with underbelly mower, plough, and some other attachments.
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
