|
Farmall & IHC Tractors Discussion Board |
Re: F-Series Serial Number Location
[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by Bill Smith on July 08, 2001 at 15:40:42 from (128.242.4.59):
In Reply to: F-Series Serial Number Location posted by Wheels on July 04, 2001 at 19:06:42:
I believe my F-20 has serial number on one of the frame rails but can't remember just where as well as on the right side of engine and on the plate on the tool box. My numbers all match up but I have seen F-20's where the numbers didn't all match up. I have heard story's that some F-20's come from the factory with nonmatching numbers becuase of a parts mix up when they were being assembled. If that is the case a serial number reading for the year of manufacturing I would think would still be accurate. However over the years some tractors have had engine and tool box swaps which messes things all up for figuring out what year a tractor is. I have even heard story's of people changing the frame rails becuase they were cracked or broke. I would think you would have to get awful abusive to break one of them becuase I have picked one up and carried it and they are pretty stout. But who is to say what might happen if you roll an F-20 over. Hard to tell what might break. If the frame rail number and the engine number are the same I would say you would be pretty good to go as far as saying that that number is the actual number but if they don't match and they lead you to a controversy of figuring out what year it is I would say you got a problem. Then the only thing you could do is maybe check out factory changes from year to year if there happened to be any. Other than the different front end I believe (not sure what year or maybe there wasn't one)and the color change in late 1936 and the flat belt to v belt later on I don't know of any on the F-20. I have never been around an F-12 or F-14.
Follow Ups:
Home
| Forums
| Order Support
Today's Featured Article -
Two-Brush Generators - by Chris Pratt. Whether for product liability or because the aftermarket parts and labor business is lucrative, this concept is disturbingly prevalent. Fortunately when you step into your shop and make that jump 50 years back in time to work with your old tractor, this concept goes out the window. Even so, when it comes to the charging system, people quickly revert to this idea and start replacing the major components one at a time until it works. The reason you don't find any decals in your replacement set wit
... [Read Article]
Latest Ad:
WANTED IH C200 gas engine — complete running motor Wanted complete used IH C200 gas engine in running condition for an International 574 gas tractor. My block has a hole in it and is dead, so a rebuild kit wont do it — need a whole running motor. The C200 also came in the 544 and 674 gas trac
[More Ads]
Copyright © 1997-2026 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|