(800) 853-2651
SHOP NOW

JD6105E PTO Question

B

Bobl1958

Well-known Member
So I am preparing for the new to me Massey mower conditioner and one of the things required is to change the PTO shaft around on my 2013 JD 6105E tractor from 540 to 1000rpm.Per the manual, I removed the keeper ring and pulled the shaft out, cleaned it up, and slid it back in with the 1000 sticking out. Re-installed the keeper. When I was putting the tractor in the shed, with no implement hooked to the PTO, I thought I would turn the PTO (electric switch) on to see how the speed read. In about 3 seconds or so a beeper started going off with an alarm symbol on the dash. The PTO light was out and it was not turning. I sbut it off and tried it again, with the same outcome. I then switched back to 540 and same thing.
I read the manual front to back and couldn't find anything on this, but I have a hunch that if the PTO shaft doesn't sense drag, it may just sound an alarm and shut itself off. I can't think that I ever engaged the PTO with nothing on the shaft. Does anyone know if this would be correct? Worried there is something wrong with the 1000 as I have never used it before, but 540 seemed to do the same. Any thoughts? Thanks
 

I have been around a 6400 and 6420, an as I recall the PTO will run without a load. Probably should connect an implement and see what happens, does the shaft even turn at first?

Is wiring intact on PTO solenoid (above and to the right of the PTO shaft, as I recall) and to the PTO shaft speed sensor (ahead of the PTO shaft)?
 
Go to page 50D-4 in your manual. You have to enter your pto speed and set it. Roll mode switch and turn signal switch are used to set the PTO speeds
Thinking that should do it for you.
 
Just a note that I started looking and found that a wire on the PTO speed sensor was cut into. I'm thinking possibly a rat chewed it, but its hard to tell, it looks cut. Soldered it back together and all is well. PTO was not sensing movement and shutting itself off. Thanks for the thoughts. Bob
 
You must log in or register to reply here.

Similar threads

M
PTO pump question
Replies
4
Views
312
mfbengel
M
super99
1655 Dual Speed PTO
Replies
2
Views
168
NEWIoliver
N
C
John Deere 4640 and 540 pto ?
Replies
8
Views
346
NY 986
N
J
2955 Pto
Replies
2
Views
131
Tx Jim
Tx Jim
C
1650 pto Shaft removal
Replies
2
Views
201
Mike(NEOhio)
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top