(800) 853-2651
SHOP NOW

Injector washer / spacer

C

CBBC

Member
Long story short I have water get into the air intake of my tracked dumper. The 4th cylinder was full of water as was the entire manifold etc
All drained and spins free now. I took the injector out to ensure it wouldn?t hydrolock.

When the injector came out there was a dimples washer right between the injector tip and the head.

Should the concave be against the injector or the head?
Hopefully pictures will load .
 
Try again.
cvphoto44499.jpg

It?s an Isuzuengine by the way.
 
I have never (personally) seen a injector sealing washer like that --- never worked on that type of motor either. Thoes two injection pump guys should know that are on here all the time -- I am sure they will be done there naps shortly.
 
Yes after carefully checking I did see marks on the injector.
I have it all back together and it?s running very smooth.

The water issue is weird and hopefully a freak incident but we will keep a bucket over the air intake or park undercover when not in use.

Thanks. Grant
cvphoto44561.jpg
 
That's NOT a sealing washer, but injector tip HEAT shield. They should be replaced anytime injector is removed. The Bosch injectors on older GM and VW use a similar shield. The inner center/up edge goes toward the injector tip.
 
Thanks DT.
Interesting to know it?s a heat shield.
Yes I installed it the way you said and it?s all running fine.
I was most concerned that I would have a bunch of rust or stuck injector with all that water. But it?s smooth.
Thanks. Grant
 
Yes it?s a Morooka it?s a MS600 with dump box.
The box is about 6? wide and 9? long.

I have a golf course top dressing box that I am going to mount
on the back and make a sander for our cranberries.
 
You must log in or register to reply here.

Similar threads

TractorDad3
Ford 901 Prepare for Setting
Replies
12
Views
952
TractorDad3
TractorDad3
V
8N Milky oil but good compression and normal spark plugs
Replies
4
Views
338
Jim.ME
J
J
Ford 3600 Diesel Loses Power/rpm Under Load
2
Replies
26
Views
2K
jedoga
J
J
Working on a '44 Model A
Replies
13
Views
531
JoeR83
J
M
Running Rough and I'm out of Ideas
Replies
17
Views
1K
Mnethercutt
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top