(800) 853-2651
SHOP NOW

3010 Value

2

2510Paul

Well-known Member
In western Wisconsin, what would this gas 3010 be worth? I am checking on hours but is relatively low, shifts tight. Estimated value should be less ROPS and JD Step Kit. The carburetor was rebuilt by Robert?s Carburetor a few years ago. I have had to put points and condenser in it a couple of times for the owner, now it is acting up again. I had rebuilt the front end and put load shaft seals in it also a couple years ago. Owner is tired of this and wants to sell.
Paul

cvphoto40357.jpg
 
https://www.tractorhouse.com/listings/farm-equipment/for-sale/list/manufacturer/john-deere/model-group/3010?InfoRequestDelay=1

https://www.machinerypete.com/listings/tractors/40-99-hp/john-deere/3010

https://www.auctiontime.com/listings/farm-equipment/auction-results/list/category/1100/tractors/manufacturer/john-deere/model-group/3010
 
If he wants to sell it $3500-4500. People are asking more but they are not getting it. There has been a few on Craigslist for a long time at big prices. Tom
 
I wonder if it has the MS carb. or a Zenith ? and if it is the MS carb. maybe that is what's acting up ? I put Echlin ignition parts in our 4020 gas back when we bought it in 1992 ? still in there working fine. I think we put 600 to 700 hours on it in all those years.
 
3010/4010's have a weak PTO set up,,along with a lot of birthdays,,and this being a Gas...not worth much,,but it does look good...the looking good part will temp a lot of people,,but they are like a hot looking Blond with a wig and cotton filled bra,,after you get her home they aren't as good as you thought...
 
Reminder to all: take the PTO spline shaft off, drill the cap screws and lace some SS wire thru them. Or tack weld them, etc. point is, they need to stay tight while running and not shift to 1000 rpm while turning. Otherwise the internal pin shears and you are in trouble.
 
One more reason to never own one. Value to me would be what I could get for it at scrap yard (not parts yard) minuse what it would cost me to get it there. Tires might be only thing of value.
 
You must log in or register to reply here.

Similar threads

EX Deere Farmer
5210 Brakes dragging issues!!!
Replies
3
Views
719
jddrawbar
J
W
1948 Ford 8N No spark/distributor problems
Replies
4
Views
3K
Jim WI
J
C
Ford 960 value
Replies
7
Views
820
Lynn Patrick
L
A
Value of a JD 70 diesel converted to a 12 volt starter?
Replies
2
Views
411
Blksmok
B
R
8N Trouble shooting
Replies
16
Views
1K
Ron Petterson
R
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top