(800) 853-2651
SHOP NOW

Allis Chalmers L59 Woods Mower

T

TASKY

New User
I picked up a L59 Woods Mower for my Allis Chalmers C. The idler and mounting frame fit a B part number 9376. I plan to cut and lengthen the B frame to fit my C unless someone has one for a C part number 9201 that wants to sell or trade mounting frames.

Does anyone have the measurements from the very edge that bolts to the final drive casings to the face of the downward facing tabs to mount the deck?

Is the deck centered under the tractor or is it offset?

When I pull up on the raising arm it looks like it is pulling up and at an angle. Is this right?

I know the rear pulley alignment is critical. Am I forgetting anything else?
 
I know what you're up against as I had an L59 on two different B's, one manual lift, one hydraulic lift. Then I got a 306?, or whatever the 6' version is. Then I switched the 306 over to a C!

Both mountings on the B's were factory- mower offset to the right, so when lifting from the right side of the tractor, the mower came up mostly straight.

I bought the wider mounting bracket for the C. But I immediately altered it so the mower deck was centered under the tractor. I built a lift with cables and pulleys from the rear rockshaft so the mower lifted from two points, and came up straight.

They're all gone now. Climbing onto those antiques got to be too much for this antique!
 
Where are you located ? I have a mounting frame four a C Allis Chalmers maybe we could make trade if you are
any where close east central Iowa .
RALPH
.
 
I am in Duluth MN. Bob thanks for the reply. I know I always come up with a plan before I leave the pilot seat. Ralph I sent you an email.
 
You must log in or register to reply here.

Similar threads

C
Putting a woods L59 belly mower on a farmall BN
Replies
6
Views
497
grandpa Love
grandpa Love
D
  • Question
Allis Chalmers B, Gemmer steering box
Replies
11
Views
561
DSMHONEYYARD
D
S
Looking for any attachments for a Woods 5215 Mow'n Mach
Replies
6
Views
443
BarnyardEngineering
BarnyardEngineering
R
Allis G Mower Brackets (Woods 42-G)
Replies
9
Views
816
mdm1
mdm1
D
Allis Chalmers ib with rotary mower?
Replies
2
Views
759
old
O
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top