JD 2510 leaking

eskandari_n1 · Sep 8, 2016

I am new and I have JD2510 suddenly start leaking hydraulic from bottom please see picture. need help where to start.

Bob Bancroft · Sep 8, 2016

Go down to the JD forum and the guys there will fill you in on the load control shaft seals, etc.

tomstractorsandtoys · Sep 8, 2016

Go to Ebay and there is a seller from IN that sells a seal and retainer that is much better than the Deere one. His uses a newer Deere seal that he makes a holder for. Make sure to replace the bushing and remove all side to side play. If shaft shows wear replace it as well and usually the front draw bar pivot bushing as well. We do several a year and the IN seals are the best I have found. Tom

Dave Sherburne, NY · Sep 8, 2016

Try /boling machine They've been making the parts you need for a long time
http://bolingmachine.com/

eskandari_n1 · Sep 8, 2016

(quoted from post at 16:29:58 09/08/16) Go down to the JD forum and the guys there will fill you in on the load control shaft seals, etc.

thanks Bob,
how difficult is to replace it?

Tx Jim · Sep 9, 2016

Ditto get Bolings Mach shop bush/seals if bushings are worn enough to require replacing.

Drain hyd oil,put L/D lever under seat in "D",remove end caps,support drawbar support with jack or come-along,slide shaft out,lower drawbar support,inspect bushings & shaft closely for wear,R&R seals. Reassemble in reverse order.

eskandari_n1 · Sep 10, 2016

thank you very much for your help. is there any bleeding needed after installation when done adding hydraulic fluid?

Tx Jim · Sep 11, 2016

No bleeding required. If air happens to get in either hyd pump just cycling steering &/or other hyd function will disperse any air.

eskandari_n1 · Sep 11, 2016

(quoted from post at 03:12:49 09/11/16)
No bleeding required. If air happens to get in either hyd pump just cycling steering &/or other hyd function will disperse any air.

what about front-end loader. does it need bleeding?

Tx Jim · Sep 11, 2016

(quoted from post at 17:16:07 09/11/16)

(quoted from post at 03:12:49 09/11/16)
No bleeding required. If air happens to get in either hyd pump just cycling steering &/or other hyd function will disperse any air.

Click to expand...

what about front-end loader. does it need bleeding?

NO

eskandari_n1 · Sep 16, 2016

I order boling seal having problem to drive it in. they told me 3020 part will work for 2510. any idea?

Tx Jim · Sep 17, 2016

L/D bushings for 2510 & 3020 are the same part number. Are you attempting to install bushings with the correct end towards trans case? Here's the spec's for JD bushing.

eskandari_n1 · Sep 18, 2016

(quoted from post at 03:11:43 09/17/16)
L/D bushings for 2510 & 3020 are the same part number. Are you attempting to install bushings with the correct end towards trans case? Here's the spec's for JD bushing.

thanks Tx Jim, it took to hammer to jammed it in.

Tx Jim · Sep 18, 2016

Thanks for update & you're welcome.
Jim

JD 2510 leaking

eskandari_n1

New User

Bob Bancroft

Well-known Member

tomstractorsandtoys

Well-known Member

Dave Sherburne, NY

Member

eskandari_n1

New User

Tx Jim

Well-known Member

eskandari_n1

New User

Tx Jim

Well-known Member

eskandari_n1

New User

Tx Jim

Well-known Member

eskandari_n1

New User

Tx Jim

Well-known Member

eskandari_n1

New User

Tx Jim

Well-known Member

Similar threads