(800) 853-2651
SHOP NOW

Long 460 Rear Hydraulics

K

khafe458

New User
Pardon my ignorance and lack of understanding ahead of time but I have been researching and not finding a lot of answers.

I recently acquired a Long 460 tractor and had a few questions on the hydraulic system. I am wondering if I can add rear remote hydraulics so I can run a baler or other equipment with hydraulic hook-ups? I am wanting to purchase a baler and start processing hay with it. I have seen them with loaders so I believe it to be possible. I attached a picture of where I believe I can tie in via the manual. It appears to have a hydraulic connection of some sort already.

I grew up and working on 8N/9N's and have no experience with hydraulic systems on tractors in general, so any education would be appreciated. I know this tractor is probably not best suited or even work for the job, but it is what I got at the moment.

Thanks in advance!
mvphoto44364.jpg
 
(quoted from post at 13:33:24 10/22/19) Do you have the lever on the right hand side just in front of the seat? Not the 3pt left lever.
Click to expand...

I do not. Just so happens I saw one for sale on the side of the road today and pulled over. Looks like I am missing that lever and some linkage. But my thought is I can buy some fittings and use the housing I have and get the lever. Anyone see an issue with this?
 
(quoted from post at 05:48:15 10/24/19) If your housing is the same it should work.Where are you located? I have several Fiat parts tractors with the remote set up.
Click to expand...

Cool. I am in east tn
 
Should be as simple as getting the hydraulic lines with couplers, flared
couplings,control handle, and linkage then install it.

TF I found a steering cylinder east of South Boston earlier this week. So
far it is working fine.
 
(quoted from post at 05:44:03 10/25/19) Should be as simple as getting the hydraulic lines with couplers, flared
couplings,control handle, and linkage then install it.

TF I found a steering cylinder east of South Boston earlier this week. So
far it is working fine.
Click to expand...

That s the plan. I want it to look like this.
mvphoto44506.jpg
 
You must log in or register to reply here.

Similar threads

T
Long 460 O Rings
Replies
4
Views
236
rustred
rustred
M
older affordable loader for a newer 5045e?
Replies
0
Views
96
MI-Bill
M
G
Ford 4000 Jerky Hydraulics
Replies
2
Views
166
Ggray
G
K
Farmall H hydraulics
Replies
13
Views
888
DeltaRed
D
W
580CK MOD 3point
Replies
3
Views
197
used red MN
U
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top