(800) 853-2651
SHOP NOW

JD 1020 rockshaft linkage question

G

Greg273

Member
I have the rockshaft apart to replace a busted o-ring in one of the valve spools. That went back together fine, but now im having some questions about the linkage. Basically, link#2 in the below diagram, are those studs supposed to be pressed in to the link? Physically joined? Because I dont see how one e-clip holds link#2 to link#4, since that stud moves freely out of #2. Now i took pics of everything before I dissasembled this back in December, but of course that phone got destroyed and lost those pics.[/img:77987a05c0]
mvphoto56531.jpg
 
I should also mention that the shaft that connects the linkage to the 3pt contol lever was slightly bent at the fulcrum just where it enters the housing... just enough so that i could not remove shaft from housing. But i was able to take roll pin out of fulcrum to remove linkage and piston housing to change o-rings in valves.
 
Well Im just gonna have to guess, since the parts drawing shows link#2 as one piece, that the bent condition of the control lever shaft somehow made the stud come apart from the link. Since this is the first one ive seen, i have nothing to compare it to. JD sells them, about $150 for that one link and $222 for the shaft, so thats my next option.
 
(quoted from post at 09:17:39 06/14/20) Well Im just gonna have to guess, since the parts drawing shows link#2 as one piece, that the bent condition of the control lever shaft somehow made the stud come apart from the link. Since this is the first one ive seen, i have nothing to compare it to. JD sells them, about $150 for that one link and $222 for the shaft, so thats my next option.
Click to expand...

I think you're correct. If it was me looking for those over priced parts I would be checking salvage yards as they should have many. Which part # cost $222?
 

The JD dealer wants $222 for the 3pt control lever shaft, part #AL60565, sub for #AL27221. I will check some salvage places.

UPDATE:
Found a few places much MUCH cheaper. Link I found used for $15, shaft I found aftermarket for $47.

Thanks Tx Jim.
 
You must log in or register to reply here.

Similar threads

A
A trivia question for the old 2 tone Case guys
Replies
7
Views
1K
L.Fure
L
B
1953 JD 50.... I'm just not expierenced enough. Venting.
Replies
11
Views
4K
CLW
C
S
Spent the week working on the tractor
Replies
7
Views
2K
Dave in MS
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top