Welcome! Please use the navigational links on your left to explore our website.

Company Logo Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Kountry Life
  
John Deere Tractors Discussion Forum
:

“A” question on Babbitt bearings

Welcome Guest, Log in or Register
Author  [Modern View]
cp1

09-20-2019 18:29:55




Report to Moderator

Rebuilding an”A” that has bad babbitt on the connecting rods. Can I have the journals cleaned up and put in rods with insert bearings? Also wondering if there is a way to narrow it down to what year it may be? The number on the plate is rubbed off. I can send a picture if that helps or is there an Internet place to go to, that would tell the differences and changes thru the years? Thanks




[Log in to Reply]   [No Email]
MSD

09-21-2019 06:20:12




Report to Moderator
 Re: “A” question on Babbitt bearings in reply to cp1, 09-20-2019 18:29:55  
With babbitt rods you can remove shims to make up for a worn crank. Unless your starting with a fresh grind, putting insert rods in could be a bit of a hassle finding bearings to fit your worn crank.



[Log in to Reply]  [No Email]
h3llbilly

09-20-2019 19:09:52




Report to Moderator
 Re: “A” question on Babbitt bearings in reply to cp1, 09-20-2019 18:29:55  
Yes sir, if it's 6-3/4 stroke, you can buy a used set of 60 insert rods and bearings. I am assuming it's not an unstyled. Slant dash or war time A's were built from '39 to '47. In '41 they went from a 4spd to a 6spd trans. The cyclone A or late style ('47 to '52) are much more obvious with square seat,square shifting quadrant, and difference in frames.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2019 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy