4020 clutch replacement?

Freddy · Dec 27, 2016

If I took a 4020 in for a clutch / flywheel replacement
at a Deere dealership how much approximately am I
look at for cost?

David G · Dec 27, 2016

My guess $1500-2000.

Does it have loader on it?

Bob · Dec 27, 2016

That MAY buy the PARTS!

Freddy · Dec 27, 2016

Yes it's equipped with a loader

DAVISFARMS · Dec 27, 2016

$2000 plus

Freddy · Dec 27, 2016

I would agree on that they want $720 just for the flywheel

tomstractorsandtoys · Dec 27, 2016

You could spend $5000 at a dealer. The last 4020 I did was $2000 and that included all new clutch parts(reman plates and fingers)2 new discs and throwout bearings,labor and a new rear engine seal.New aftermarket flywheel should be around $500.Loader makes very little difference as most shops just roll the back half away. I do several a year for neighbors. Tom

Dave H · Dec 27, 2016

freddy, I guessed you already asked the dealer and am holding that card down?

David G · Dec 27, 2016

Why would you not surface the flywheel if not too bad?

Freddy · Dec 27, 2016

Yes I just thought it was quite high! Yet they do have high over head.

Freddy · Dec 27, 2016

It actually is a Chinese flywheel. It has many spider heat cracks and shows signs of warping. High blue spots. Ridges that form spokes outward. Have not seen anything like that and for $400 dollars for a USA built one ( that what they told me) I am not taking that risks. Seen a broken flywheel knock a hole in a bell housing once.

Freddy · Dec 27, 2016

Thanks tom on your insite.

Mike M · Dec 28, 2016

What type of clutch disc was running against that flywheel ? A ceramic one ?

Freddy · Dec 28, 2016

Just a normal looking woven one. Now the disk looked newish, but the rest looked not the same! So the answer is it could of had one earlier. Pressure plate broke .

tim s · Dec 28, 2016

One of the things you can get into on older 3020/4020 clutches is if the fly wheel got turn too many times the pressure plate will hit in the outer radius of the fly wheel and not put full pressure on the clutch plate,,, they will sorta work for a bit then slip badly...and on most of them they have been turned a few times for sure...

ben brown · Dec 28, 2016

(quoted from post at 10:31:24 12/27/16) If I took a 4020 in for a clutch / flywheel replacement
at a Deere dealership how much approximately am I
look at for cost?

i have to look tomorrow just did 4020 clutch flywheel replacement last mouth used the new button clutch and replaced flywheel was out specks

ben brown · Dec 30, 2016

did this 4020 aug.. fly wheel clutch kit with release bearing pilot rear seal run right at 2k

Freddy · Dec 30, 2016

Was this a Deere dealer or a individual professional that performed this replacement? Shopping
around can save big bucks I have seen.

ben brown · Dec 30, 2016

(quoted from post at 11:04:23 12/30/16) Was this a Deere dealer or a individual professional that performed this replacement? Shopping
around can save big bucks I have seen.[/quot
i repair farm equipment that was what i charged for doing the it.

4020 clutch replacement?

Freddy

Member

David G

Well-known Member

Bob

Well-known Member

Freddy

Member

DAVISFARMS

Member

Freddy

Member

tomstractorsandtoys

Well-known Member

Dave H

Member

David G

Well-known Member

Freddy

Member

Freddy

Member

Freddy

Member

Mike M

Well-known Member

Freddy

Member

tim s

Well-known Member

ben brown

Member

ben brown

Member

Freddy

Member

ben brown

Member

Similar threads