38” pressed steel Wheels for my A

alabamafrog · Aug 17, 2008

I need two 38” pressed steel wheels for the back of my 48ish styled A. I currently have rusted 34” wheels on it from an MT and nothing on the front. I have heard that you can still buy these wheels new. Anyone know where I could find a set and about how much it would cost? I would like to finish this tractor but funds are kinda low right now.

Anonymous-0 · Aug 17, 2008

if you have a number i might be able to hook you up with a set. if you have an ebay account or know someone who does that is also a good place.

alabamafrog · Aug 17, 2008

I've been watching ebay for several weeks and haven't seen any. What number do you need? If you mean part number then I'd have to look it up, if you mean phone number then I can email you that.
Thanks,

happydeere · Aug 17, 2008

if you want you can email me your phone number i can check the part number on my a tomorrow when i go out to the barn but my neibor may have a set or there is a swap meet up around here next weekend i could defiantly locate a set for you there. my email is johhnypopper@yahoo

happydeere · Aug 17, 2008

is thier any paticular width do you want the standard 12.4 or wider?

Anonymous-0 · Aug 17, 2008

hello
i have a set on my 51 A that have a new looking set of 12.4 x 38 firestone 23deg i might be willing to sell due to going wider.email is open.

Anonymous-0 · Aug 17, 2008

here is a picture

Seppo · Aug 17, 2008

I have a set that might work for you. Blasted and painted 4 years ago but never mounted.

alabamafrog · Aug 18, 2008

I’m not wanting to make a puller, just wanting to put it back as close to stock as I can and still being as economical as I can. I have a set of 13.6-38 tires that Bamapuller gave me but I could put them on my 60 if I found rims with tires for the A.

alabamafrog · Aug 18, 2008

ricky c, your email may be open but there is not a link for it at the bottom of your posts so I can't figure out how to get to it but I'm definitely interested if I can afford them and its not too far to drive to get them.

Dandy Don · Aug 18, 2008

"ricky c", Where are you located Ricky?

Don

PBrowning · Aug 18, 2008

Alabamafrog -- You simply place the cursor on "Send Mail" & left click. Presto, you have a formatted email in front of you -- you are good to go.

And if you would enter your email at the top of your post, others could email back to you! For some stupid reason, people want to be contacted, but are too lazy to enter their email! Baffling!!

Anonymous-0 · Aug 18, 2008

west columbia south carolina 29172

Anonymous-0 · Aug 18, 2008

[email protected] 803-955-9008

alabamafrog · Aug 20, 2008

PBrowning,
I couldn't figure out what you were talking about until I switched from modern view to clasic view and there it is plain as day. Guess sometimes the old stuff is better than the modern. All of my posts automatically have link buttons for my email, profile, and tractor picture website in the modern view, I’ve never used the classic view before.
Thanks for the tip,

38” pressed steel Wheels for my A

alabamafrog

Well-known Member

Anonymous-0

Well-known Member

alabamafrog

Well-known Member

happydeere

Member

happydeere

Member

Anonymous-0

Well-known Member

Anonymous-0

Well-known Member

Seppo

New User

alabamafrog

Well-known Member

alabamafrog

Well-known Member

Dandy Don

Member

PBrowning

Well-known Member

Anonymous-0

Well-known Member

Anonymous-0

Well-known Member

alabamafrog

Well-known Member

Similar threads