Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Implement Alley Discussion Forum

Speaking of IH plows...

Welcome Guest, Log in or Register
Author  [Modern View]

04-09-2013 06:08:58

Report to Moderator

Going to look at a couple of Little Genius trip plows, the one I am mainly interested in is a 1-16 to pull with my little 60 Oliver. Can parts be had for the moldboard, or can something be altered and fitted? Just curious.

[Log in to Reply]   [No Email]

04-28-2013 12:31:52

Report to Moderator
 Re: Speaking of IH plows... in reply to CumminsMan, 04-09-2013 06:08:58  
Can anyone shed some light on this plow I recently acquired?

Would this be the plow chief or super chief style? I need plow points, any place that sells them?

Can we still get these from CIH?
third party image

[Log in to Reply]  [No Email]

04-09-2013 18:57:50

Report to Moderator
 Re: Speaking of IH plows... in reply to CumminsMan, 04-09-2013 06:08:58  
It depends on the wings that are mounted. The old one piece "Plow Chief" wings are hard to get parts for. The replacement (in the late 1950's) "Super Chief" has two pieces to the wing and one piece plow points and the points can be found almost anywhere. The Plow Chiefs might have a two piece point or a one piece point with a thickened and extended point on the front end. You can replace the entire plow and change a Little Genius from a "Plow Chief" to a "Super Chief" arrangement but it will be a little pricy. If the plow has a wear shin at the front of the wing you have a "Super Chief" plow. The "Plow Chief" wing was all one piece.

[Log in to Reply]  [No Email]

04-09-2013 08:21:04

Report to Moderator
 Re: Speaking of IH plows... in reply to CumminsMan, 04-09-2013 06:08:58  
I do have a few very good 16" shear and moldboards if it ends up needing one. Bob

[Log in to Reply]  [No Email]

04-09-2013 14:44:17

Report to Moderator
 Re: Speaking of IH plows... in reply to Bobl1958, 04-09-2013 08:21:04  
Bob, The moldboard is in great shape. May be interested in a shear though. My email is open. Thanks

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums

Copyright © 1997-2023 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy