(800) 853-2651
SHOP NOW

power major pneumatic governor

7

780 prairieboy

Member
Have a power major with pneumatic governor that is giving trouble, upon taking governor housing off I discovered that the rubber diaphram was spilt and the small valve that goes into the diaphram retaining screw on one end(the one with rounded head and small hole in it)and into the adjustable damping valve assembly. THIS VALVE IS MISSING ,do have the threaded housing with locknut , tried to obtain one thru fuel injection repair shops and fordson dealers ,all advise this is an obsolete part. I did get a replacement diaphram but unable to locate a valve. does anyone have this part or able to provide a detailed drawing that I could get a machine shop to make one?
 
Hi I am trying to post an exploded diagram of the pnuematic governor. I think I've still got a couple of old pumps etc SOMEWHERE in the barn. If you let me know whwt part you need I'll try to sort it out for you. I can't make any promises but I'll give it a go. Looks like I've got the size wrong Sorry MTF
2vt1cw0.jpg
 
thanks for the reply. I require all three pieces shown in fig 71 , the bolt with round head, the taper valve and the threaded piece with bushing. does not matter if the taper valve is long or short as long as the part with bushing matches.
 
OK I look later today and come back to you. I dont remember seeing these bits for ages but I'm sure they are still there somewhere. MTF
 
Hi Prairieboy. You are in luck. One of my old pumps still has the part on it. I will send you the complete end with what feels like a good diaphram etc all still in it. Just give me your postal address and i'll send it off tomorrow. Maybe any bits of it that you dont need you will pass on. MTF
 
Hi I got your message. Where are you then I can let you know the approx postage I dont even know what country you are in. I dont want anything for this item but I would appreciate it if you could pay the postage. MTF
 
have been trying to send e-mail to you thru forum it looks like you are not getting them please repy back to me .I think you have my e-mail
 
You must log in or register to reply here.

Similar threads

A
Fordson Power major with cracked hydraulic cylinder
Replies
1
Views
596
Aursis
A
B
tools (and the way they usually work)
Replies
10
Views
2K
Goose
Goose
B
Super Major
Replies
0
Views
1K
Barrett Scotland
B
N
Why independent mechanics can stay in business...
Replies
14
Views
5K
JMOR
J
B
ZANE'S Hydraulic Troubleshooting
Replies
2
Views
747
ZANE
Z
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top