(800) 853-2651
SHOP NOW

Quick update on the 1841 project

R

Royse

Well-known Member
I brought this tractor home last February to be this winter's project.
It needed a little work. Obviously.

Today I got to drive it under it's own power for the first time.
A lot of work left to do. Some temporary hookups still in place.
But it runs and drives. The Sherman reverser works as designed.

Power steering is all working well other than a little water in the fluid.
I think that water got into the replacement cylinder as the PO had it stored outside.

So far, other than the battle getting the right clutch, all is well.

mvphoto47722.jpg


mvphoto47723.jpg


mvphoto47724.jpg


mvphoto47725.jpg
 
[size=18:7d5811583a][/size:7d5811583a]
Glad that one, is gonna be a good one for you.
Did you say that the front lights are the same size as the one's I have on the 3000 ROP???? If you want to use these lights in the 1841 grill, ?????? If you remember I told you I was going to send them to you anyway......so I can send them in time for you to put them in that grill.
Just let me know when you need them!!! They both work, but as you sent me a set of the "BRIGHT" Lights, I'm not ever going to use the ones that are on the ROP!!!

Gary
 
Thanks Gary, I always like to keep the original lights around.
I'm not sure which way I'm going to go on this one yet.
It will be a work tractor, so I may put LED's in there too.
I like the bright lights. Wish there were some in the mirror! :lol:
 

Heh. You might need to file an environmental impact statement for that oil spill, Royce. Looks about like what I had a couple of years ago when I slid a turkey roaster pan under the hydraulic reservoir of my 871, unscrewed the plug, and went into the house to wash up. :shock:
 
Hello Royse , I wish I knew you had a reverser in your tractor I would have told you to check the shifter shaft as they are noted for breaking off . I just made two dozen new shift shafts this past summer because no makes any parts for the reversers and I repair a lot of them so I had to bite the bullet and make some .
 
Thanks Tony, I think it is working Ok, meaning it will reverse using
the lever but this is the first Sherman reverser I've had so I don't
know much about them other than what I've read here.
 
It'll be alright Fred, it's on cement so I can clean it all up.
I had a large drain pan under it which caught most of it, but then
I lowered the front and the hydraulic lines leaked a bunch more
 

"I lowered the front and the hydraulic lines leaked a bunch more"

Silly Dude;
I don't think that a 'Diego Rake' is gonna look good on that tractor.

Do something else......(Paint it PINK!!!)

GB
 
You must log in or register to reply here.

Similar threads

jon f mn
Weekend project
Replies
1
Views
615
john in la
J
jon f mn
Truck project done
Replies
16
Views
574
fastfarmall
F
stevieb49829
Update on a couple of related things
Replies
0
Views
501
stevieb49829
stevieb49829
J
Back on the roof
Replies
18
Views
776
dpendzic
D
J
Update on the 504D
Replies
5
Views
491
Gene Davis (Ga)
G
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top