(800) 853-2651
SHOP NOW

7710 Rear Arms Not Moving

If the linkage is turning the shaft that goes inside the top cover and the arms aren't lifting, then it could be something internal to the top cover, or it could be the pump isn't pumping.
 
Thanks, Sean. The shaft to the lift cover is moving. My pressure at the pump taken right above the line to the dual power is 125 psi at idle at cold start. After running a few minutes, the pressure drops to 55-60 psi at idle. The rear arms do not move at all and the only fluctuation I see in pressure is when I switch the dual power from high to low or vice versa.
 
The pump in that tractor is actually two pumps in one body. The front part is the main pump for the 3 point lift, which should be able to create well over 2000 psi. I believe that the rear part of the pump is for both the independent PTO and dual power and generates much less pressure, somewhere in the 160 psi range I believe.
 
The PTO works, I have nothing hooked to the remotes to see but, was told they were working. Does the relief valve in the priority pack control the rear arms or is there another relief valve inside the lift housing? Thanks for the help.
 
(quoted from post at 11:33:30 01/13/19) The PTO works, I have nothing hooked to the remotes to see but, was told they were working. Does the relief valve in the priority pack control the rear arms or is there another relief valve inside the lift housing? Thanks for the help.
Click to expand...

I said that there are two pumps in there. The 3 point pump pressure is independent of the other pump that powers the PTO clutch and dual power. If the remotes do indeed work then the 3 point pump should be working fine, but is that just what you were told by the person that sold you the tractor?
 
After more checking, there little to no pressure at the remotes. The main pump is new, I removed it today and it is visibly fine. This tractor has a trailer brake valve that is supplied directly off the top of the pump. Can this valve cause no pressure to the remotes and three point? I removed the priority valve and disassembled, it looks good and all the valves are moving freely.
 
You must log in or register to reply here.

Similar threads

P
Three point linkage arms raising and lowering w/o lever
Replies
1
Views
338
alltron
A
F
Ford 7710
Replies
1
Views
332
peckens
P
J
anybody noticed ?
2
Replies
38
Views
3K
NDIHC
N
F
Ford 7710 pto
Replies
5
Views
376
Bern
B
R
Leak under my 3400 1974 tractor
2
Replies
20
Views
3K
Sean in PA
S
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top