Welcome! Please use the navigational links on your left to explore our website.

Company Logo Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Kountry Life
  
Ford Tractors Discussion Forum
Order Ford NAA Parts Online

Jubilee Throttle control rod settings and no throttle range

Welcome Guest, Log in or Register
Author  [Modern View]
jmunday

03-24-2017 09:44:42




Report to Moderator

Hello,
Can someone give me advice on how to properly set the throttle control rods. The problem that I'm having is I don't have any throttle range, I'm either idling or wide open. Adjusting for something in between is really difficult and requires small bumps of the lever. Also I'm not using half of my throttle arm travel. I can be wide open by pulling the arm lever about half way down. I did rebuild the carbuerator and I'm pretty certain everything went back together right. It runs great it's just hard to set to a specific rpm. Any advice is much appreciated.

[Log in to Reply]   [No Email]
WayneIA

03-24-2017 14:42:39




Report to Moderator
 Re: Jubilee Throttle control rod settings and no throttle range in reply to jmunday, 03-24-2017 09:44:42  
Short rod with cleves on front end pins to the lower hole in the governor arm and carburetor, Long rod ,with spring hooks to top hole in governor arm and to throttle bell crank



[Log in to Reply]  [No Email]
showcrop

03-24-2017 10:27:12




Report to Moderator
 Re: Jubilee Throttle control rod settings and no throttle ra in reply to jmunday, 03-24-2017 09:44:42  
It sounds like your linkage is not installed correctly. There is a good description in your owner's manual on adjusting the governor linkage which will also help you to confirm that you have the rods connected properly.



[Log in to Reply]  [No Email]
jmunday

03-24-2017 10:13:23




Report to Moderator
 Re: Jubilee Throttle control rod settings and no throttle ra in reply to jmunday, 03-24-2017 09:44:42  
Quoting Removed, click Modern View to see

Okay thanks. I'm betting weak spring. The spring looks pretty used and abused. I'll start there.



[Log in to Reply]  [No Email]
old

03-24-2017 10:07:20




Report to Moderator
 Re: Jubilee Throttle control rod settings and no throttle range in reply to jmunday, 03-24-2017 09:44:42  
Gov to carb linkage can be in a bind some place or a weak or broken spring will also cause that.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Restoration Story: 1964 JD 2010 Dsl - Part 2 - by Jim Nielsen. Despite having to disassemble the majority of my John Deere 2010's diesel engine, I was still hopeful I could leave the engine-complete with crankshaft and camshaft-in the tractor. This would make the whole engine rebuild job much easier-and much less expensive! I soon found however, that the #4 conrod bearing had disintegrated, taking with it chunks of the crankshaft journal. As a resul ... [Read Article]

Latest Ad: need 3 point arms (with the ball) especially need the [More Ads]

Copyright © 1997-2021 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy