961 front dimensions

Welcome Guest, Log in or Register

Author

[Modern View]

Tom Bond

02-23-2017 17:17:13

Report to Moderator

Would anyone know the exact dimensions or know where they would be available for the 4 front mounting bolts on the bolster? I checked my T&I and service manuals but nothing in there. The top is 6" center to center and the bottoms are 4". Just looking for something exact before I start milling and drilling a piece of 1/2" cold rolled for a mounting plate and eye attachment for pulling. If not available, I guess I'll just tap out a template on cardboard and hope for the best.
third party image

[Log in to Reply] [No Email]

kirk-nj

02-25-2017 00:22:32

Report to Moderator

Re: 961 front dimensions in reply to Tom Bond, 02-23-2017 17:17:13

Stiff cardboard and a ballpeen hammer might be your best solution.

Kirk

[Log in to Reply] [No Email]

Greg NE

02-23-2017 19:39:45

Report to Moderator

Re: 961 front dimensions in reply to Tom Bond, 02-23-2017 17:17:13

No dimensions for you but I built a front hitch/tie down point a couple of years ago for my 971 and all I did was take a straight edge and drew a line in pencil horizontally between the center of both sets of holes so I knew the vertical distance and then went off the centerline to layout the holes in a 1/2" plate. Fit like a glove when I was done but maybe I got lucky. My 2 cents worth. Greg NE

[Log in to Reply] [No Email]

Stevob671

02-23-2017 18:47:13

Report to Moderator

Re: 961 front dimensions in reply to Tom Bond, 02-23-2017 17:17:13

Sorry to late to go out and measure right now, but that wide angle shot sure gives an interesting perspective!

[Log in to Reply] [No Email]

Ultradog MN

02-25-2017 04:54:28

Report to Moderator

Re: 961 front dimensions in reply to Stevob671, 02-23-2017 18:47:13

Is that what it is - wide angle?
It's a great photo.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Today's Featured Article - Trenching With a Plow - by Staff. Introduction: This interesting information came from one of the discussion forums here at YT. We thought we should place it up front so it could be read by anyone interested in putting old iron to work. [Editor] I tried something new today, and it worked so well I thought I should post it - in case it might help someone else. I'm running 100 yards of 4" drain pipe from the gutter downspouts of our house to a pond down the hill. This should hel ... [Read Article]

Latest Ad: 990 7 foot mower conditioner john deere hay rake pto driven john deere head carrier [More Ads]

Copyright © 1997-2021 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Welcome! Please use the navigational links on your left to explore our website.

961 front dimensions