(800) 853-2651
SHOP NOW

Pivoting on what Pivot Pin to use on my TO30. Man I'm bushed

B

Bill in Brunswick

Member
There are two pivot pins and two bushings available for the TO30 on this site, but the dimensions don't mean anything to me. Nothing seems to ring true with what I'm reading in the Dealer Shop Manual. Are the words "swept back axel" what I'm supposed to key off of? I guess that's what I have because the axel is........ swept back.
My other Fergie details are....... according to "Jim in Ohio"'s serial number chart, it's an early 52 model with a serial number in the 74,000 range.

Any help is greatly appreciated! Thanks
 
the parts book is showing only one pivot pin assembly for the TO 30 and that is part number 180 499 M91 the dimensions are 4-3/4" long, with a 7/8" bolt hole. Swept back axle, yes.
 
Thanks for the reply, Richard. Unfortunately, neither the part numbers nor the dimensions of the pins on this site match the part book numbers you gave.

The two pins to pick from this site are:
1 3/4 Dia. 4 1/4 Length (Part No: 825002M1)
and
1 3/4 OD 4 3/4 Long for swept back axle 5/8 bolt hole and 1" dia. crank hole (Part No: 183221M1)

What do you think? Go with the last one?


They also list two bushings:
2.075" OD, 1.750" ID, 0.820" Long for swept back axle (Part No: 182850M1)
and
1 15/16 OD, 1 25/32 ID, 1 1/2 Long (Part No: 180344M1)

The first bushing sounds right ?

Also, how many bushings do I need? I saw a post somewhere that mentioned two.

Again, thanks for the help !!!!!
 
Bushing 180 344 M1 is what the parts book is calling for and yes you need 2. The length is 4-3/4" what you need to do now is find out what size your bolt is because that is where the other size comes into play. The parts book is only showing one part number for the 30 and that uses a 7/8" bolt. Richard
 
as long as you are probably going to order from this site give them a call and see if they can give you any more help. Your handle says Brunswick where is that?
 
Thanks Richard. That's a good idea. Maybe their 5/8" is a typo and should be 7/8". I'll also pull the bolt on my TO and see what size it is.

Thanks for confirming the 2 bushings as well.

And my Brunswick is in Ohio.

Merry Christmas and thanks for all the help.

Bill
 
You must log in or register to reply here.

Similar threads

stevieb49829
Progress on the 101 Jr front rebuild-this is LONG
Replies
5
Views
563
Stan Coryell
S
L
'53 ferguson to30 front axle pivot pin issue
Replies
2
Views
1K
Lamina1982
L
J
TO30 Pivot pin and bushing
Replies
3
Views
871
Jeremy in DE
J
H
What to look for on an Oliver 1800
Replies
5
Views
1K
ss55
S
L
Mopping up a Tuneup on my 9N
Replies
15
Views
3K
lastcowboy32
L
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top