(800) 853-2651
SHOP NOW

Harry Ferguson TO 30 with a frontend loader

M

MFTO30.mills

New User
Any assistance will be greatly appreciated. I have just bought a Harry Ferguson TO30 with a frontend loader
The tractor itself, other than its missing the hood is in what I would consider better than average condition everything works as it should, seems to run strong
Biggest problem is that the front pump , shaft and harmonic balancer pulley adapter is missing and I need a replacement
 
Congratulations, you have a very good tractor to work with. Your parts are available here on the parts link top of the page,”Ferguson”, and look at the
hydraulic parts there, also Steiner tractor is a great source.
 
(quoted from post at 04:12:29 08/07/20) Congratulations, you have a very good tractor to work with. Your parts are available here on the parts link top of the page,"Ferguson", and look at the
hydraulic parts there, also Steiner tractor is a great source.
Click to expand...


Thank you for your reply, to be honest I'm still unsure of specifically the correct part due to there being missing completely.


Any chances you might know the exact patt numbers for those three items ?
 
Can't do that. FEL was aftermarket add on. Who did it? PO or dealer? That actually would not make much difference at this age. Your best
bet might be a trip to the local Case or New Holland dealer and get some part numbers and a pic. You should at least buy the hex drive
shaft and the pulley mount from them for the troubles of looking it all up for you.
Be glad you have a TO-30. The loader front pulley might still be in production. The TO-20 pulley is totally obsolete.

1753729M91 is your hub mount number and them comes the Part No: L78-13 shaft mount. Beyond that is the shaft and good luck on that as well
as the pump itself.
Go over to the 8N Ford board and see what you get for info. Ebay might be your friend if someone is parting out a machine.
Surplus center hydraulics might also be your friend.
I haven't had to look for this stuff for many years. Now I have two machines with a FEL and another two machines without FEL.
Then a few machines. . . .
 
You must log in or register to reply here.

Similar threads

V
Massey Ferguson 232 loader problems
Replies
8
Views
770
Vincetaylor54
V
F
IH 484 Loader Tractor
2 3
Replies
47
Views
2K
MARK ROBKE
M
N
8N with a loader, and questions
Replies
17
Views
2K
deanostoybox
D
B
Replacing loader valve on a Freeman 4000 loader
Replies
16
Views
1K
Determined
D
8
Will This Loader Work With A Long Nose 8N?
Replies
2
Views
797
8NChris
8
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top