TRACTOR PARTS Allis Chalmers Case & David Brown Farmall & International Ferguson Ford & New Holland John Deere Massey Ferguson Massey Harris Minneapolis Moline Oliver & Cockshutt Kubota / Yanmar

TRACTOR MANUALS

Allis Chalmers	Case	Farmall IH	Ford 8N,9N,2N	Ford
Ferguson	John Deere	Massey Ferguson	Minn. Moline	Oliver

Marketplace

Community

Galleries

Research & Info

Miscellaneous

Related Sites

Discussion Forum

Radiators ???

Welcome Guest, Log in or Register

Author

bronco

05-30-1999 21:07:21

Report to Moderator

What model Farmall tractor's radiator will interchange with the Super A's , since they seem to be hard to find???

[Log in to Reply] [No Email]

Jim

06-01-1999 07:39:31

Report to Moderator

Re: Radiators ??? in reply to bronco , 05-30-1999 21:07:21

Most older IH radators can't be recored because of the way the tanks are put on.

[Log in to Reply] [No Email]

Mike

06-03-1999 17:49:29

Report to Moderator

Re: Re: Radiators ??? in reply to Jim, 06-01-1999 07:39:31

I just had a radiator for an "A" recored. Costed about $200.

[Log in to Reply] [No Email]

Stan(VA).

06-01-1999 04:53:59

Report to Moderator

Re: Radiators ??? in reply to bronco , 05-30-1999 21:07:21

Best bet would probably be a later A or B(say '44-'47). The C radiator would fit but since it has different spacing from the front of the motor you would need to switch the radiator neck(that bolts to the head) and sheet metal around too (the C hoods are an inch or so longer than the A/B hoods).
Stan(VA).

[Log in to Reply] [No Email]

Jim Becker

05-31-1999 06:36:59

Report to Moderator

Re: Radiators ??? in reply to bronco , 05-30-1999 21:07:21

This may not be totally accurate, as I am just answering off the top of my head. The A/B radiator is probably the same, except the early ones that used a different hood/grille attachment method. The C radiator might be usable but is different due to the pressure cap.

Recoring is probably your best bet.

[Log in to Reply] [No Email]

Wayne

05-31-1999 04:58:11

Report to Moderator

Re: Radiators ??? in reply to bronco , 05-30-1999 21:07:21

I don't know but will a C or B. Recoring would be another option.

[Log in to Reply] [No Email]

[Options] [Printer Friendly] [Posting Help] [Return to Forum] [Log in to Reply]

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home | Forums

Today's Featured Article - Massey Ferguson 35 (and up) Tractor Assembly Notes - by Jack Wetmore. These assembly notes are for Massey Ferguson tractors with a two stage clutch and 6 speed, 8 speed and mutli-power transmissions. I see a lot of discussion forum messages regarding damaged clutches from improper assembly. The objective is to have the engine and transmission slide together safely and easily until the gap between the two halves is less than 1/4", BEFORE tightening any of the bolts holding the two together. Using bolts to draw the two halves together will damage the PTO ... [Read Article]

Latest Ad: combine ih 303 403 101 151 503 615 with grain plat header control [More Ads]

Copyright © 1997-2021 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy

Welcome! Please use the navigational links on your left to explore our website.

Radiators ???