|
| |
Need help finding parts for a IH and SMTAD!!!
| Author |
|
|
larry
07-02-2001 05:30:49
|
Does anyone know where I can buy restore or real good guages for the hood and the fuel pressure guage? also need the drip cup for the carb.Looking for a set of front weights and a glass or plastic IH precleaner and some other small parts Thanks for any help Larry
|
|
|
|
Michael Soldan
07-02-2001 19:02:13
|
|
Re: Need help finding parts for a IH and SMTAD!!! in reply to larry, 07-02-2001 05:30:49
|
|
| |
Larry ,front wheel weights are hard to find. Not every one ran them and those that remain have been snapped up by our tractor puller friends. I looked all over southern Ontario for a set and couldn't find any...was on a trip to Oregon and found a set up near Corvallis south of Portland...hauled them all the way home to Ontario in the back of the van,so they are hard to come by and will likely fetch$150 for the pair in the north east...I got mine for $60...I wonder what it cost in extra fuel to haul them home????. So good luck in finding some and good luck on your M. My weights are going on an H.
|
|
|
|
larry
07-02-2001 05:34:55
|
|
Re: Need help finding parts for a IH and SMTAD!!! in reply to larry, 07-02-2001 05:30:49
|
|
| |
Like to find a good hour meter for it also Thanks Larry
|
|
|
|
The Red
07-02-2001 07:17:16
|
|
Re: Re: Need help finding parts for a IH and SMTAD!!! in reply to larry, 07-02-2001 05:34:55
|
|
| |
Larry on the gauges give Ken Updike a call at 608-455-2411.
|
|
|
[Options]
[Printer Friendly]
[Posting Help]
[Return to Forum]
[Log in to Reply]
Home
| Forums
Today's Featured Article -
The Collection of a Lifetime - by Sherry Schaefer. The larest gathering of orphan tractors ever assembled by one collector will be auctioned off on May 15 in Rock Island, IL. Ed Spiess was a well known tractor buff who spent most of his time dreaming of rare and unknown tractors. His background as an agricultural engineer sparked his interest in the unique attributes of the models built from 1939-1959.
... [Read Article]
Latest Ad:
Need a clutch shaft for a 46 Massey Harris 101 Jr., F162 Continental engine. About 18.25 inches long, to fit 1-1/8x 10 spline clutch disk. Bare shaft without sprocket or bearing is OK.
[More Ads]
Copyright © 1997-2021 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
|
