|
| |
| Farmall & IHC Tractors Discussion Forum |
656 hydro
| Author |
[Modern View] |
|
Greg NE
05-30-2020 20:19:03
|
I tried the archives but couldn't find an answer so here I am. I have a friend that is going to pickup a 656 hydro with a stuck motor and I'm just wanting to be sure it is able to be towed onto the trailer or if there is a disconnect somewhere so it will roll. I'm more of a Ford guy and well acquainted with the Select O Speeds and the disconnect they have so they can be rolled around. I know the hydros are a completely different animal and my only experience with anything similar are lawnmowers and they have a release to move them when the engine isn't running. Thanks in advance! Greg NE
|
|
|
|
|
Greg NE
05-31-2020 16:05:42
|
|
Re: 656 hydro in reply to Greg NE, 05-30-2020 20:19:03
|
|
| |
Thanks for the replies!! We got it loaded with no problems. The lever on the right side is rusted tight, won't move at all. We couldn't really read the decal on the left side anymore so we just guessed and put the handle in the middle where it can move from side to side. We could back right up to it and we just winched it on at a slow pace and all went good after we blocked the loader up and chained the 2pt blade up so it was off the ground also. Thanks again Greg NE
|
|
|
|
calfeeder
05-31-2020 03:50:59
|
|
Re: 656 hydro in reply to Greg NE, 05-30-2020 20:19:03
|
|
| |
Be sure the low neutral high lever on right side is in neutral. Damage to hydro can happen. Don't ask me how I know
|
|
|
|
504
05-30-2020 20:44:50
|
|
Re: 656 hydro in reply to Greg NE, 05-30-2020 20:19:03
|
|
| |
depends which hydro system he has. The most common is the forward revers handle is on the right side of the dash,the high, neutral, revers is on the right. Put the high low in neutral and winch it on. BTW, the steering my not work at all,take a pipe to adjust the steering.
|
|
|
[Options]
[Printer Friendly]
[Posting Help]
[Return to Forum]
[Log in to Reply]
Home
| Forums
Today's Featured Article -
Talk of the Town: Removin Broken Bolts - by Staff. Another great discussion from the Tool Talk Discussion Forum. The discussion started out with the following post: " How would I remove a bolt thats broken off in a piece of metal and I want to save the treads in the metal and then put in a new bolt. "
... [Read Article]
Latest Ad:
for sale New mamifold for IH 504 tractor 100 plus shipping
[More Ads]
Copyright © 1997-2021 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
|
