(800) 853-2651
SHOP NOW

Cross 3pt for 560

L

Luke470

Member
I've got a 560 with drawbar. Looking at putting 3pt on it.
Was wondering if anyone had experience with the cross 3pt conversion kit? Good quality? How's the install?

Thanks
 
The Cross is a brand, i cant say i ever heard of that one,, but i put a Cornhusker brand on my 806, that is a heavy built one, that's been copied buy a lot of secondary company's since. Has it it got 1 or 2 lift cylinders ?
 

They have one that comes with one cylinder and one that comes with 2. Thinking the two cylinder would have more lifting capacity?
 
Cross is at Mindenmines MO, near Joplin.

Give them a call
Cross Machinery & Manufacturing

301 Main St, Mindenmines, MO 64769

(417) 842-3405
 

Thanks!

How do the hydraulic cylinders plumb into the tractor hydraulics? Do you just run hoses to one of the remotes?
 
My 560 outside control lever, shorter one, goes to LH valve under the hood. Pipe from that valve runs to back coming out under the seat. I run my 3pt off that valve as it is handyiest for m e. I use quick couplers because I may want to remove it. Depending upon type cylinders you use, single or double acting you will have to turn little button coming through the bottom of the dash. My second valve handle in controls valve on the far right under dash and it has hoses running to the back of the operator platform with break away couplers. I have also hooked 3 point to that at times which ever one works easier for you
 
I've got one of the Cross 3-point hitches. It is the light one, and single-cylinder. My 1950 Farmall H has twisted the center round bar, during plowing, to where the right-side draw bar had dropped several inches. I had to have it taken apart, replaced and re-welded. I'm thinking if a 1950 H can twist one, more or less ruin it, then the Cross must be pretty light-weight. I believe my brother has a heavy-duty Cross on his H, with no problems.
 
You must log in or register to reply here.

Similar threads

3
Needing Factory made 3pt for H
Replies
9
Views
571
AlinMO
A
G
Farmall 560 Hydraulic issue
Replies
2
Views
275
Janicholson
Janicholson
8
560 run a backhoe?
Replies
11
Views
450
caterpillar guy
C
W
The “new” 560
Replies
9
Views
836
Ellis Kinney
Ellis Kinney
W
560 Valve setting
2
Replies
23
Views
810
WHFarms
W
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top