Welcome! Please use the navigational links on your left to explore our website.

Company Logo Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Kountry Life
  
Farmall & IHC Tractors Discussion Forum
:

424 ih seal

Welcome Guest, Log in or Register
Author  [Modern View]
warrenwoodrow

10-03-2016 12:23:52




Report to Moderator

Can I replace the seal on rear of hydraulic lift reservoir from outside of reservoir / This is oil plunger seal which seals the the plunger which operates draft control .




[Log in to Reply]   [No Email]
warrenwoodrow

10-03-2016 15:44:21




Report to Moderator
 Re: 424 ih seal in reply to warrenwoodrow, 10-03-2016 12:23:52  
The seal is located under the part called " power Arm " and described as " top link crank "



[Log in to Reply]  [No Email]
Bob

10-03-2016 20:45:33




Report to Moderator
 Re: 424 ih seal in reply to warrenwoodrow, 10-03-2016 15:44:21  
Yes, but there's also an O-ring INBOARD of the seal, in a groove in the pin.

NOT sure if replacing the oil seal alone will stop a leak. MAY be just a dirt wiper??? (I ASSUME you have a leak at the pin?)



[Log in to Reply]  [No Email]
warrenwoodrow

10-04-2016 08:34:28




Report to Moderator
 Re: 424 ih seal in reply to Bob, 10-03-2016 20:45:33  
Thanks for the reply. Yes, I have seen the o ring on the diagram. All I know for sure is that oil leaks at the opening that the seal is at. Do you know if o ring can be inserted from outside without pulling the top off of reservoir. I am hopeful that if seal is removed that it is possible to pull o ring out from outside and push a new one on. I may just try the seal first. It appears to be constructed in similar fashion to a p t o shaft seal . By that I mean it has the inner spring which holds rubber seal tension on the pin/ plunger.

[Log in to Reply]  [No Email]
warrenwoodrow

10-04-2016 08:44:55




Report to Moderator
 Re: 424 ih seal in reply to warrenwoodrow, 10-04-2016 08:34:28  
The more I look at the diagram it appears my best bet may be to replace the seal from outside and see if it stops the leak. Otherwise it appears that there is another seal as well as the o ring that you mentioned which could be leaking as well. I believe I would have to get the top off of it to be able to remove and replace those two.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Product Review - by Staff. When we finally checked out the 3000 PSI North Star, the whole story chaned. This unit was equipped with an 11 HP Honda engine with fuel shutoff, adjustable flow and optional syphon degreaser dispenser. It didn't have a pressure release or electric start to facilitate easy starting but according to the instructions, simply pulling on the trigger while cranking was sufficient. This method of starting proved more than adequate and kept the cost down on the unit. It had all the important ... [Read Article]

Latest Ad: 1967 Ford 3000 [More Ads]

Copyright © 1997-2021 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy