Welcome! Please use the navigational links on your left to explore our website.

Company Logo Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts

Community
Discussion Forums
Project Journals
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Kountry Life
  
Case Tractors Discussion Forum
:

Somewhat a CASE ?

Welcome Guest, Log in or Register
Author  [Modern View]
Dale in Nw wa

08-13-2013 21:36:54




Report to Moderator

OK I have a Question? My 469 NH swather eats the bushings in the sickle Bar. I went out and cut about a 1/2 acre this morn. lost bushing, went in town got two more at 25 bucks a piece then went and paid 10 to get pushed in. thought about what is causing this sickle bar has been in use for a long time so went and got a new sickle bar put my new head on cut 5 acres lost new bushing. the guards are less than year old hold down clips and wear plates are ok anyone have a thought about what is causing this. OH and when I was cutting grass hay if I got into real short and real thick grass it would hammer real hard so I would drop to 1st gear in the DC as it is leading the 469 around. Thanks Dale Hubbard.

[Log in to Reply]   [No Email]
Allan2012

08-14-2013 13:24:47




Report to Moderator
 Re: Somewhat a CASE ? in reply to Dale in Nw wa, 08-13-2013 21:36:54  
I agree, it sounds like your knife is out of register, you have to have the wobble box in exactly the middle of it"s stroke before you tighten your knife bolt. Other wise the rubber bushing won"t twist the same amount both ways and will burn up in no time. Also check to see if your knife bolt is worn, you may need a new one if the bolt is out of round. I hope that this has helped you out.



[Log in to Reply]  [No Email]
Dale in Nw wa

08-14-2013 21:01:00




Report to Moderator
 Re: Somewhat a CASE ? in reply to Allan2012, 08-14-2013 13:24:47  
The bolt was a brand new grade 5 bolt with double nuts got hot enough to raise a very large blister on finger it was that hot. Thanks for the info I never knew about centering it thanks Dale



[Log in to Reply]  [No Email]
Julie needs your help!

08-22-2013 04:33:11




Report to Moderator
 Re: Somewhat a CASE ? in reply to Dale in Nw wa, 08-14-2013 21:01:00  
we've been messing with sickle bars,etc too- does anyone know why a pea header reverser would not be working?



[Log in to Reply]  [No Email]
John Saeli

08-14-2013 06:05:08




Report to Moderator
 Re: Somewhat a CASE ? in reply to Dale in Nw wa, 08-13-2013 21:36:54  
Dale: If the sickle bar is new, & guards are sharp, I'd say the sickle is out of "register". Full stroke left, sickle point should be centered under a guard, then full stroke right, the same sickle should be centered under the next guard right. Also, the best sickle section on the market is the Heavy, Top Serrated, Coarse Section.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Massey Ferguson 35 (and up) Tractor Assembly Notes - by Jack Wetmore. These assembly notes are for Massey Ferguson tractors with a two stage clutch and 6 speed, 8 speed and mutli-power transmissions. I see a lot of discussion forum messages regarding damaged clutches from improper assembly. The objective is to have the engine and transmission slide together safely and easily until the gap between the two halves is less than 1/4", BEFORE tightening any of the bolts holding the two together. Using bolts to draw the two halves together will damage the PTO ... [Read Article]

Latest Ad: combine ih 303 403 101 151 503 615 with grain plat header control [More Ads]

Copyright © 1997-2021 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy