| |
Case Tractors Discussion Forum |
what is it ?? easier
Author |
[Modern View] |
Case Nutty 1660
07-31-2011 19:51:14
|
 this a NOS Case item any one reconize it last one was to hard I guess, and am talking about the item in the crate not sitting by it cnt
|
|
|
1031D
08-02-2011 07:14:48
|
Re: what is it ?? easier in reply to Case Nutty 1660, 07-31-2011 19:51:14
|
|
Oleclint, that is a model 356 one way disk, 5 blades, 3.5ft cut, 10" spacing. dc741, do us all a huge favor and call the nearest recycling yard, have them send out every available man and torch and cut up every fricken thing you own so we don't have to listen to all your negative sh!t anymore about cutting everything up and sending it to china!!!!!!!! Just make sure you go in the dumpster with it all!
|
|
|
oleclint
08-01-2011 17:28:32
|
Re: what is it ?? easier in reply to Case Nutty 1660, 07-31-2011 19:51:14
|
|
 CaseNutty , I enjoy your "tests" of what is it? .I grew up with Case , brings lots of memories back . If I can get it done on here, I will try to post a pic of our CASE 1 way. As of now, know one has been able to I D the model . It is the only one that I have ever seen. We use it for making a fire break if needed. Also worked it recently on cleared brush land. clint
|
|
|
oleclint
08-01-2011 17:32:40
|
Re: what is it ?? easier in reply to oleclint, 08-01-2011 17:28:32
|
|
 another photo of Case 1 way. no rain on this ground for 7 weeks in middle of Oklahoma. Clint
|
|
|
D-C-741
08-01-2011 21:27:46
|
Re: what is it ?? easier in reply to oleclint, 08-01-2011 17:32:40
|
|
It Looks like the 1 we have,dont use it any more/Its in the pile to be cut an sent to China.
|
|
|
1031D
08-01-2011 07:34:04
|
Re: what is it ?? easier in reply to Case Nutty 1660, 07-31-2011 19:51:14
|
|
Tom, what is that drawbar for leaning up against the crate? Looks like a model R disk, if it is, got any good pictures of it?
|
|
|
Case Nutty 1660
08-01-2011 08:39:33
|
Re: what is it ?? easier in reply to 1031D, 08-01-2011 07:34:04
|
|
Jim you are correct it is a "R" drawbar new never assembled, have several pieces of it all new hyd control gane frames one or two spools, I thinkt the manual levers got it on a parts buy deal cnt
|
|
|
Klyde
07-31-2011 20:15:44
|
Re: what is it ?? easier in reply to Case Nutty 1660, 07-31-2011 19:51:14
|
|
Case Nutty 1660
07-31-2011 20:18:42
|
Re: what is it ?? easier in reply to Klyde, 07-31-2011 20:15:44
|
|
yes it is !!! fits a 700, has the Case eagle stenciled on the crate, also have five in the box units for model 75 pulltypes also and lot of NOS screens not looking to sell though cnt
|
|
|
[Options]
[Printer Friendly]
[Posting Help]
[Return to Forum]
[Log in to Reply]
Home
| Forums
Today's Featured Article -
Massey Ferguson 35 (and up) Tractor Assembly Notes - by Jack Wetmore. These assembly notes are for Massey Ferguson tractors with a two stage clutch and 6 speed, 8 speed and mutli-power transmissions. I see a lot of discussion forum messages regarding damaged clutches from improper assembly. The objective is to have the engine and transmission slide together safely and easily until the gap between the two halves is less than 1/4", BEFORE tightening any of the bolts holding the two together. Using bolts to draw the two halves together will damage the PTO
... [Read Article]
Latest Ad:
combine ih 303 403 101 151 503 615 with grain plat header control
[More Ads]
Copyright © 1997-2021 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
|