| |
Case Tractors Discussion Forum |
CC rebuild kit
Author |
[Modern View] |
ShaggyM
02-27-2011 15:18:14
|
Where someone get a sleeve and piston kit for a CC? Actually the complete kit would be real nice! Thanks!
|
|
|
JTs randr
03-02-2011 05:46:46
|
Re: CC rebuild kit in reply to ShaggyM, 02-27-2011 15:18:14
|
|
You might as well but a set of sleeves and pistons in it because I will guarentee you that once you pull the sleeves to put in new o rings there gonna be pitted beyond belief. Best just to overhaul it completly and be dun. It's not cheap but better thing to do.
|
|
|
wilson
02-27-2011 16:31:03
|
Re: CC rebuild kit in reply to ShaggyM, 02-27-2011 15:18:14
|
|
be very sure to replace o rings at bottom of sleeves. Even if just taking head off tractor that has not been opened up for years I pull sleeves and install o rings
|
|
|
in-too-deep
02-27-2011 15:30:11
|
Re: CC rebuild kit in reply to ShaggyM, 02-27-2011 15:18:14
|
|
From what I understand, the C series uses the same internal engine parts as the D series. You can get rings and gaskets on this site, and I don't believe it's a sleeved engine.
|
|
|
Jim McVay
02-27-2011 15:44:46
|
Re: CC rebuild kit in reply to in-too-deep, 02-27-2011 15:30:11
|
|
ShaggyM
02-27-2011 15:34:40
|
Re: CC rebuild kit in reply to in-too-deep, 02-27-2011 15:30:11
|
|
Thanks! I have never had one apart so this is a new thing for me.
|
|
|
[Options]
[Printer Friendly]
[Posting Help]
[Return to Forum]
[Log in to Reply]
Home
| Forums
Today's Featured Article -
Massey Ferguson 35 (and up) Tractor Assembly Notes - by Jack Wetmore. These assembly notes are for Massey Ferguson tractors with a two stage clutch and 6 speed, 8 speed and mutli-power transmissions. I see a lot of discussion forum messages regarding damaged clutches from improper assembly. The objective is to have the engine and transmission slide together safely and easily until the gap between the two halves is less than 1/4", BEFORE tightening any of the bolts holding the two together. Using bolts to draw the two halves together will damage the PTO
... [Read Article]
Latest Ad:
combine ih 303 403 101 151 503 615 with grain plat header control
[More Ads]
Copyright © 1997-2021 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
|