(800) 853-2651
SHOP NOW

More On The CASE 201 Combine Engine Pics.

A

Adirondack case guy

Well-known Member
This is a 201Case engine sn.2676376 off of a 660 combine we sold new. As you can see it is still on the engine frame complete with rad. and pulley drive housing. One thing to note about this engine, it utilized a Pierce external belt driven govenor. I have a question for you case guys. The timing cover on this engine is not machined for the internal gov. which is on other engines. So, will a 148 timing cover and gov. assy. bolt up to this engine? I haven't taken time to do any compareing in the parts books.
a29491.jpg

a29492.jpg
 
Hey old friend mr DCTOM Seems the motors in question fit-up to vac tractors. I have access to 2 vac's for the right price. I always wanted to make a small 4 wheel tractor with more power than just one of the motors. Hers what I am thinking, will any of the larger motors bolt up to a vac and them I and using pto and floping the differental on one of them make something like a small stiger??? thr otyer option I have considered is making a small dozer out of the one vac that the motor is not stuck
 
Yes it does. If you remember my pulling 300B at McFaddens a couple of years ago! That has the 201 block with the 148 front plate.
 
Hi Brad
How are things going for you. I ment to post back the other day when you posted here, but----. Do you have any plans to come back up this coming year? Scott and I haven't added to our collection this year, but I would like to get this 201 into my 1957 310 dozer.I still got some nice pics. of you pulling the 2 and 300 at Sunucrest.
 
hey all you too bill, the 201 wont fit a vac with out some modifition , bell houseing is bigger, must have vac fly wheel redrilled to fit 201 crank for vac starter will work
 
Lots of time if you want it to look good. Been there done that. Pulled our VAC with this combo in #3500 thru #4000 with 14.9x38, plenty of snort. Dave S
 
If I remeber right the 660 I had. Had a hydraulic pump above the oil filter and had athe govenor under the front cover. I will check later today. The motor is still in the shed. It sure was a nice runner.
Bob
 
You must log in or register to reply here.

Similar threads

C
1960 case 540 torque tube sections fill one to fill all
Replies
9
Views
479
used red MN
U
J
Case 480ck gas engine governor not holding load
Replies
5
Views
1K
used red MN
U
R
Identify the engine on my '81 445 Loader
Replies
8
Views
734
Sean in PA
S
R
Case 660 Combine on Big Iron Auction
Replies
15
Views
1K
Don Rudolph
D
W
Case 660 Combine questions
Replies
4
Views
1K
WICaseGuy
W
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top