Welcome! Please use the navigational links on your left to explore our website.

Company Logo Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Discussion Forum

Re: Hydraulics for a WC

[Show Entire Topic]  

Welcome Guest, Log in or Register

08-13-2002 22:53:59

Report to Moderator

NO-Castings between the engine and beyond are all different.

[Log in to Reply]   [No Email]

08-14-2002 11:14:45

Report to Moderator
 Re: Re: Hydraulics for a WC in reply to JMS/MN, 08-13-2002 22:53:59  
Did not Allis Chalmers have a mechical lift availble for the WC? I think I remember seeing WCs with cultivers on them. I think they had somthing to do with the pulley drive on the side. Did I dream this or does someone know about this? Sid

[Log in to Reply]  [No Email]
John (C-IL)

08-14-2002 12:53:29

Report to Moderator
 Re: Re: Re: Hydraulics for a WC in reply to Sid , 08-14-2002 11:14:45  
Sid, the mechanical lift bolted to the top of the driveline between the transmission and the differential. Problem was that you had to be in a forward gear to get the thing to work. John

[Log in to Reply]  [No Email]

08-14-2002 13:34:29

Report to Moderator
 Re: Re: Re: Re: Hydraulics for a WC in reply to John (C-IL), 08-14-2002 12:53:29  
John, it would work standing still if you put down the rear disconnect lever and left it in a any forward gear. In that respect it isn't a lot different than hydraulics. The negative is that it is two position and the position is not easily changed. I've been toying with the idea of using this lift to lift a three point setup on my WC so I could use it for shredding. Where do you get a round to it?

[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums

Copyright © 1997-2020 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy