Welcome! Please use the navigational links on your left to explore our website.

Company Logo Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Kountry Life
Allis Chalmers Discussion Forum


Welcome Guest, Log in or Register
Author  [Modern View]
jerry mA

09-28-2010 06:26:40

Report to Moderator

i have a chance to get a belt pulley for a 190 but the guy says there no lever to turn it on does it run off the pto lever JERRY

[Log in to Reply]   [No Email]

10-04-2010 18:57:30

Report to Moderator
 Re: 190 in reply to jerry mA, 09-28-2010 06:26:40  
The guy is wrong. There would be a lever that stick up out if the torque tube just behind the clutch. It would have a plug in that location when no pulley was installed. You will need to get the bevel gear and spacers from the clutch shaft as well as the lever and shift fork.

[Log in to Reply]  [No Email]
jerry mA

09-28-2010 18:06:01

Report to Moderator
 Re: 190 in reply to jerry mA, 09-28-2010 06:26:40  
thanks guys for the replay will look and see JERRY

[Log in to Reply]  [No Email]

09-28-2010 16:57:38

Report to Moderator
 Re: 190 in reply to jerry mA, 09-28-2010 06:26:40  
If I remember right, look above the area the pulley slides into--may be a lever on top of the trans case.If you had the pulley, a handle and rod connected to the lever and came out somewhere by the dash. I pretty sure it was not run by the PTO lever.

[Log in to Reply]  [No Email]
cole in mo.

09-28-2010 16:57:27

Report to Moderator
 Re: 190 in reply to jerry mA, 09-28-2010 06:26:40  
I can't tell you on the 190, never say one with a pully, my 14 has one, but it also has a lever to ingage it.

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums

Today's Featured Article - Product Review: JB Weld - by Staff. JB Weld is basically an epoxy glue that does an exceptionally good job of bonding to cast iron and steel along with several other materials. As I mentioned, it is so common that I have yet to buy a tractor that did not have JB Weld used somewhere. It is sometimes used so well you can't tell its there and other times used as a sloppy quick fix. Finding where and how it can be used correctly is key to whether you are using it as an "inelegant hack" or an integral solution to difficult and expens ... [Read Article]


Copyright © 1997-2020 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy