FREE SHIPPING on orders above $249.99! Details

• Tractor Parts

• Engine Kits

• Carburetors

• Salvage

• Manuals

• DVDs

• Hats

• Contact Us

• Shipping Rates

• Return Policy

• Ordering Help

• Company Info

• Parts Warranty

• Forums

Allis Chalmers D17 Parts

Category: Steering

[Categories] [All D17 Parts] [All Allis Chalmers Models]

Pivot Pin Assembly - Includes: 70916896 (7/8 inch NF slotted nut) and 70925721 (5/32 inch X 2 inch cotter pin). For tractor models (170, 175 gas with roll shift front axle), (180, 185, 190, 190XT, 200, D19 all with roll shift front axle), (D17 serial number 38136 and up with roll shift front axle). (Item #: 104301, Ref: 70235154) $65.00

Seal - Seal with wear sleeve for tractors with dual front wheels, except HD axle, serial number 42001 and up. For tractor models 160, 170, 175, 180, 190, 190XT, 200, 6060, 6070, 6080, 7000, D10, D12, D15, D17. (Item #: 164159, Ref: 70235120) $15.30

Seal, Power Steering Pump Driveshaft - For tractor models D10, D12, D14, D15, D17, WD, WD45. Verify measurements of 1.002 inches outside diameter, .437 inches inside diameter and .375 inches in width. (Item #: 173648, Ref: 1751651M1) $6.40

Spindle Bushing - Used on spindle 70237434, on tractor models (170 late), 175, 180, 185, 190, 190XT, 200, (500, 600 forklift), (6060, 6070 with standard tread, 96 inch tread), 6080, 615, (7000 early), D10, D12, D14, D15, (D17 early with 5 bolt wheel), D19, 160, 1600. (Item #: 110538, Ref: 70211743) $13.00

Spindle Thrust Washer - For tractor models (170 late), 175, 180, 185, 190, 190XT, 200, (500, 600 forklift), (6060, 6070 with standard tread, 96 inch tread), 6080, 615, (7000 early), D10, D12, D14, D15, (D17 early with 5 bolt wheel), D19, 160, 1600. (Item #: 111696, Ref: 70218762) $6.40

$Allis Chalmers D17 Spindle, LH\RH$
Spindle, LH/RH - This spindle measures A=12 inches, B=1.610 inches, C=1.625 inches, D=1.187 inches. For tractor models 170 Late, 175, 180, 185, D15, D17. Uses wheel bearing kit part number SBKAC2. (Item #: 100091, Ref: 70270038) $166.00

$Allis Chalmers D17 Spindle, LH\RH$
Spindle, LH/RH - This spindle measures A=12 inch, B=1.610 inch, C=1.500 inch, D=1.187 inch. For tractor models D10, D12, D14, D15, D17 early serial number with 5 bolt wheel. Uses wheel bearing kit part number WBKAC1. (Item #: 100090, Ref: 70237434) $293.00

Spindle, Used - For Allis Chalmers tractor models D10, D12, D14, D15, D17 (early with 5-bolt wheel), Replaces Allis Chalmers OEM number 70237434, Right or Left Side, Dimension A: 12.000", Dimension B: 1.610", Dimension C: 1.500", Dimension D: 1.187", For a new version of this item use Item #: 100090, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 400090) $160.01

No
Picture
Steering Arm - Left Hand For D14, D15, D17, D19, 170, 175, 180, 185, 190, 190XT, 200 (Item #: 100105, Ref: R2824) $117.00

Steering Arm - Left Hand, Used - For Allis Chalmers tractor models D14, D15, D17, D19, 170, 175, 180, 185, 190, 190XT, 200, Replaces Allis Chalmers OEM number 70245867, 1.610 inches inside diameter, Left Hand, For a new version of this item use Item #: 100105, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 497088) $75.01

Steering Arm - Right Hand, Used - For Allis Chalmers tractor models D14, D15, D17, D19, 170, 175, 180, 185, 190, 190XT, 200, Replaces Allis Chalmers OEM number 70245868, (1.610 inches inside diameter), Right Hand, For a new version of this item use Item #: 100106, Used items are not always in stock. If we are unable to ship this part we will contact you within one business day., (Item #: 497155) $83.01

Steering Arm, LH - Fits 1.610 inch diameter hole, keyed spindle, ball joint hole taper is .625 inch to .725 inch. For tractor models 170, 175, 180, 185, 190, 190XT, 200, D14, D15, D17, D19. (Item #: 100105, Ref: 70245867) $117.00

Steering Arm, RH - Fits 1.610 inch diameter hole, keyed spindle, ball joint hole taper is .625 inch to .725 inch. For tractor models 170, 175, 180, 185, 190, 190XT, 200, D14, D15, D17, D19. (Item #: 100106, Ref: 70245868) $141.00

Steering Shaft Cross and Bearing (U-Joint) - Tighten up your steering with a new Universal Joint. This part measures 2.305 inches across cap to cap, with a 0.968 inch cap diameter. Used on Allis Chalmers D14, D15, D17, D19, RC when using later style steering joint # 224825, WC when using later style steering joint # 224825, WD, WD45 Diesel, WF when using later style steering joint # 224825. Replaces OEM numbers 10P715, 1KAR758, 224890, 350254R91, 357439R91, 363313R91, 363321R91, 52977DAX, 70224890, 836514M91, 841193M92, A20435, A20684, A30408, A30425, A30428, A30435, VTA3227, Z862 (Item #: 115351, Ref: 70224890) $11.00

Steering Wheel - Steering wheel, 3 spoke. 18 inch diameter, 7/8 inch shaft. Round hub with pinhole. For tractor models WC, WD, WD45, (D14 serial number 19001 and up), (D17 serial number 24001 and up). Replaces: 70229677, 70202260, 229677, 202260. (Item #: 101404, Ref: 70229677) $49.40

Steering Wheel - For D10, D12, D14, D15, D17, D19, D21. Steering Wheel. 17 1/2 inch diameter, splined hub. Black Plastic with Covered Spokes. Diamond Center AC Logo available as part number R3996. Also replaces 232033. (Item #: 101405, Ref: 70232033) $62.15

Steering Wheel - For D10, D12, D14, D15, D17, D19, D21. Steering Wheel. 17 1/2" Diameter, Splined Hub. Creme Plastic with Covered Spokes. Diamond Center AC Logo Available as Part#R3996. Replaces 70233857, 70233851, 233851 (Item #: 101406, Ref: R3993) $56.00

Steering Wheel - For WD, WD45, Styled, WC, Early D14, This steering wheel is for tractor models D15, and D17 with 18 inch diameter, 7/8 inch Smooth Hub with pin hole. Replaces OEM numbers V2260 and 202260. (Item #: 101404, Ref: 202260) $49.40

Steering Wheel Center Logo - For D10, D12, D14, D15, D17, D19, D21. CHROME Steering Wheel Center Logo used on 70232033 and 70233851 steering wheels. Replaces 70228474, 70233852, 70246724 (Item #: 101407, Ref: R3996) $20.70

Steering Wheel Emblem Decal - 1-1/2 inches x 1-1/2 inches Black and Orange on White decal. Used as a steering wheel emblem on later model that did not use the metal emblem. (Item #: R5167) $3.50

Steering Wheel Nut - This steering wheel nut measures 13/16 inch 20 UNEF Thread. It has a black oxide finish. Used with the following steering wheels (when steering shaft has 13/16 -20 UNEF thread): 1671945M1 385156R1, 366557R2, 70232033, 70233851, A20456, 303051951, 400217R1, 242933, 10A23441, A61007. Replaces 1021464M1, 525743M1, 525743V1, 25743M1, 1853123M1, 10A31498, 208584, 252471, 35114002, 35A14002, 35P51, 367232R1, 368576R1, 70252471, A14567, F19646 (Item #: 126721, Ref: 35P51) $8.00

No
Picture
Steering Wheel, Black - 17-1/2" diameter, splined, covered steel spokes. For tractor models D10, D12, D14, D15, D17, D19, D21. (Item #: 101405, Ref: 70232033V) $62.15

Steering Wheel, Cream - For D10, D12, D14, D15, D17, D19, D21. Steering Wheel. 17 1/2 inch diameter, splined hub. Creme Plastic with Covered Spokes. Diamond Center AC Logo available as part number R3996. (Item #: 101406, Ref: 70233851) $56.00

Steering Worm Shaft Bearing - This Steering Worm Shaft Bearing has a 1.197 inch inside diameter, a 1.700 inch outside diameter and is 455 inch wide. It fits (D14, D15, D17 Rear wormshaft bearing, manual steering only), D19 (rear wormshaft bearing, manual steering only - 1 used per tractor) Replaces original part numbers: 228150, 70228150. (Item #: 126732, Ref: 70228150) $16.00

Tie Rod Assembly - Consists of OEM part numbers 70250140 and 70250141. Replaces: 249418, 225280, 225279, 254662, 254661. For (D14, D15, D17, D19, WD, WD45 Fits these models if cut to length), (170, 175, 180, 185, 190XT, 200 fits these models with standard front end). (Item #: 100082, Ref: 70254660) $52.00

Tie Rod Clamp - For Allis Chalmers tractor models D14, D15, D17, D19, 170, 180, 185, Compatible with Massey Ferguson tractor models 50 (s/n 528163-533422), 65 (Gas s/n 671680-692932 or Diesel s/n 667918-692932), 150, Compatible with Massey Ferguson Combine (s) 32, Compatible with Massey Ferguson Construction and industrial models 304, Replaces OEM number CLP12, (Item #: 104281) $4.20

Tie Rod End, Female - 17.500 inches long. For tractor models 180, 185, 190, 190XT, 200. Will also fit 170, D14, D15, D17, D19 if cut to proper length. Can also replace 250142 used on WD, WD45 if cut to length. (Item #: 100083, Ref: 70254661) $23.60

Tie Rod Male - Tie rod end with tube, outer. For adjustable front axles. 16-1/2 inches to center of post. 0.812 inch diameter. 50 inch minimum thread, not for Hi-Clear. For 180, 185, 190, 190XT, 200, D17, D19. (Item #: 100084, Ref: 70254662) $25.50

Upper Steering Wheel Shaft Bushing - Inside diameter .883 inch, outside diameter 1.125 inch, thickness .995 inch. For the following models: D14, D15 (2 used), D17 (2 used), D19 (2 used), D21, I600 (2 used), 180, 185, 190, 190XT, 200, 210, 220, 600. Replaces 206968, 228188, 228255, 70206968, 70228188, 70228255. (Item #: 122000, Ref: 364527R91) $9.30

Universal Parts and Accessories
Category: Steering

Eaton Power Steering Pump Replacement - This Power Steering Pump replaces the Eaton style belt driven Power Steering Pump. It also replaces Eaton part numbers: 503-1005-005, 20928 and P761. This is a Redesigned Pump that uses a bearing instead of original bushing. It can also be adapted to tractors using Char-Lynn Power Steering with an Eaton Pump. Please note that this pump does not include brackets, top mounted reservoir, or pulley. Some applications will require a new pressure hose to be made for a 5/8-18 inch inverted flare type fitting. The shaft diameter measures .670 inches. The shaft length, where the pulley mounts measures .575 inches. There is a 2 inch thick pump housing where the bracket bolts on. Pressure is preset at 1.32 GPM. (Item #: 113730, Ref: S03-1003) $417.87

Filter, Power Steering - Filter case size is 3 inches diameter and 1 1/2 inch height. Center hole is approximately 7/8 inch diameter. VERIFY size before ordering. It is used on tractors with Eaton style power steering pumps. (Item #: 111126, Ref: AE33538A) $13.20

Power Steering Pump Pulley - This Power Steering Pump Pulley is used with S03-1003 Power Steering Pump. It is designed for Tractors using Eaton Style power steering pump. It is made of Stamped steel. Measures 5 inches outside diameter, 0.675 inch bore, 1/8 inch keyway, 0.9715 inch total width for 1/2 inch belt (Item #: 164438, Ref: ABC1417) $47.60

Steering Wheel Spinner, Bare Aluminum - Comes with mounting hardware. (Item #: 108667, Ref: R3275) $8.20

Steering Wheel Spinner, Blue - Comes with mounting hardware. (Item #: 108664, Ref: R3279) $8.70

Steering Wheel Spinner, Green - Comes with mounting hardware. (Item #: 108666, Ref: R3278) $13.40

Steering Wheel Spinner, Orange - Comes with mounting hardware. (Item #: 108660, Ref: R6323) $15.10

Steering Wheel Spinner, Red - Comes with mounting hardware. (Item #: 108663, Ref: R3277) $9.10

Steering Wheel Spinner, Yellow - Comes with mounting hardware. (Item #: 108665, Ref: R3280) $8.24

No
Picture
Wheel Spinner- Black - Wheel Spinner, black knob, universal. WSV124B (Item #: 108662, Ref: R3276) $8.70

Call 800-853-2651 to Order
Or Click the "Add to Cart" Button

Category: Steering

[Categories] [All D17 Parts] [All Allis Chalmers Models]

Order Toll Free
(800) 853-2651
Mon-Fri 7am-7pm CT

Order online
anytime!

YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us!

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Website Accessibility Policy

Privacy Policy