Welcome! Please use the navigational links to explore our website.

Company Logo
View Cart
 

• Tractor Parts
• Engine Kits
• Carburetors
• Manuals
• DVDs
• Hats
• Books


• Contact Us
• Shipping Rates
• Return Policy
• Ordering Help
• Company Info
• Parts Warranty
• Forums


Allis Chalmers D10 Parts

Category: Electrical System

[Categories]   [All D10 Parts]   [All Allis Chalmers Models]  



NOTE
Alternator
- Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1952 & newer). Just call us at 800-853-2651.
NOTE

Allis Chalmers D10 Alternator Bracket Kit
Alternator Bracket Kit
- This Alternator Bracket Kit fits tractor models B, [C, CA must trim 1 inch off lower end of adjustment bracket and re-drill hole to clear draglink], [D10, D12, D14 lower bracket only], IB. Use with 8NE10305SE alternator and existing belt. (Part No: ACS2347)
$48.23

Allis Chalmers D10 Battery Cable
Battery Cable
- Battery cables, ground. For D10, D12. ``17" Long (Part No: 70241893)
$15.95

Allis Chalmers D10 Distributor Cap
Distributor Cap
- For 4 Cylinder Clip Type Cap for Delco Distributors. B, C, (CA engine serial number CE-149840 and up), D10, D12, D14, D15, D17, (WC, WD, WD45 serial number 136318 and up). Replaces Delco 811735 and 70225733. (Part No: 1750411M91)
$6.60

Allis Chalmers D10 Distributor Dust Cover
Distributor Dust Cover
- Fits early Delco Distributor with Clip Held Cap. For tractor models B, IB, C, G, CA, WD, WD45, WC, WF, D10, D12, D14, D15, D17, D19, RC. Replaces 225734 & 70225734. (Part No: 1900119)
$6.75

Allis Chalmers D10 Distributor Shaft Bushing and Shim Kit
Distributor Shaft Bushing and Shim Kit
- Delco Distributor Shaft Bushing and Shim Kit. Fits tractor models B, C, IB, RC, WC, WD, WF, CA, D10, D12, D14, D17, D19, G, WD45, D15, H3, I40, I400, I500, I60, I600. With 1112461, 1112601, 1112655 1111411 or 1112607 Delco Distributor and Clip Held Cap. Replaces: bushing: 225773, 70225773, 0.005 inch shim washer: 225797, 70225797, 0.034 inch washer: 250977, 70250977, 0.010 inch shim washer: 4050123, 74050123. (Part No: ABC3007)
$22.95

Allis Chalmers D10 Distributor Terminal Insulator Assembly, Delco
Distributor Terminal Insulator Assembly, Delco
- This Delco Distributor Terminal Insulator Assembly is for Square Shoulder (outside terminal). Note: As distributors can be changed over time, it is best to double check which style you require. This is only a guide of what was original. Fits distributor housings with 0.300 Inch diameter round hole with a keyway. If not sure, measure before ordering. Fits Allis Chalmers with Delco 1112461, 1112601, 1112655, 1111411, 1112607, 1112609. Replaces: 225791, 225792, 225793, 225794, 225795, 70225791, 70225792, 70225793, 70225794, 70225795 (Part No: 1904376)
$15.00

No
Picture
Distributor, Rebuilt
- Complete rebuilt distributor. For model D10. Add $80.00 core charge to price (will be added after order is placed when ordering online) - this charge is refundable if you send your core to us. (Part No: 1112609)
$157.71

No
Picture
Distributor, Rebuilt
- For tractor models D10, D12, D14, D15, D17 all built between 1959 and 1965. Add $80.00 core charge to price (will be added after order is placed when ordering online) - this charge is refundable if you send your core to us. (Part No: 1112593)
$157.71

Allis Chalmers D10 Electronic Ignition Conversion Kit, 12 Volt Negative Ground
Electronic Ignition Conversion Kit, 12 Volt Negative Ground
- This Electronic Ignition Kit is for Delco Distributors in the below listed models. Replaces points & condenser with an electronic module. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increase horsepower, improve fuel economy. Compatible with all 12-volt negative ground systems and 6-volt systems that have been converted to 12-volt negative ground. For tractor models G, B, C, CA, WC, WD, WF, WD45, D10, D12, D14, D15 and D17. NOTE: On those models that use a Distributor Dust Shield, you may be required to drill a larger hole in the Dust Cover for the Electronic Parts to fit properly. (Part No: 1142)
$106.75

Allis Chalmers D10 Fuse Holder
Fuse Holder
- Mounts on 5/8 inch diameter hole. 2 spade connectors. Replaces 230246, 70230246 (Part No: 376852R91)
$11.25

Allis Chalmers D10 Generator
Generator
- 6 volt, 35 amp. For tractor models D10 serial number 3501 and below, D12 serial number 3000 and below, D14 serial number 19000 and below. Refundable $25.00 core charge will be added to orders. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. Replaces 79004800. (Part No: TG-72)
$303.29

No
Picture
Generator, 12 Volt
- Pulley not included. For tractor models D10, D12, D14, D15, D17, D19 all from 1959-1965. Replaces 1100305. Refundable $25 core charge will be added to your order after processing and will not show on your order confirmation. (Part No: 1100332)
$236.64

Allis Chalmers D10 Generator, 12 Volt
Generator, 12 Volt
- Pulley not included. For tractor models D10, D12, D15, D17, D19 all from 1961-1964. Replaces 1100426. (Part No: 1100321)
$377.55

Allis Chalmers D10 Generator, 6 Volt
Generator, 6 Volt
- Pulley not included. For tractor models D10, D12, D14 all gas built from 1957-1960. Replaces Delco #1100025, 1100029, 1100034, 1100039, 1100042, 1100052, 1100055, 1100504. Add $25.00 core charge to price (will be added after order is placed when ordering online), this charge is refundable if you send your core to us.``IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. (Part No: 1100052)
$263.93

No
Picture
Generator, Delco Type, 12 Volt
- For tractor models D, D10, D12, D14, D15, D17, D19, DD, H3, HD3, RT40. Replaces Delco part number 1100305. Remanufactured. Refundable $50.00 core charge will be added to your order. (Part No: TG-59)
$242.55

Allis Chalmers D10 Ignition Kit, Delco Clip-Held Cap Distributor
Ignition Kit, Delco Clip-Held Cap Distributor
- Ignition kit for a Delco distributor with CLIP held cap. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT. Contains points, condenser, and rotor. For: A, B, CA, G, WD, WD45, D10, D12, D14, D15, D17, D19, C, E, F, 60, 66, 72, 90, WF, I40, I400, I500, I60, I600, H3. For Delco distributor numbers 1112461, 1112601, 1112655, 1111411, 1112607. (Part No: ATK1DCR)
$7.34

Allis Chalmers D10 Key Switch
Key Switch
- 5 terminal, with keys and jam nut. For tractor models D10, D12, (D14 from serial number 9500 and up), (D15 up to serial number 9000), (D17 up to serial number 75000), D19, D21. Replaces 235785, 231705, 233320, 229201, 234356 70235785, 70231705, 70233320, 70229201, 70234356. (Part No: 230163)
$45.29


NOTE
STARTER
- Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!
NOTE

Allis Chalmers D10 Solenoid Switch
Solenoid Switch
- Solenoid Switch, 6-volts For tractor models using Delco Starters 1108036, 1107466, 1107474, 1107905, 1107025, 1107977, 1107092. For B, C, 100, D10, D12, D14 Replaces 70223334, 223334. (Part No: 142364HA)
$5.99

Allis Chalmers D10 Solenoid Switch
Solenoid Switch
- Solenoid and manifold heater switch, 12-volt. Super sedes 233296. For tractor models D10, D12, D14, D15, D17. (Part No: 70237136)
$14.98

Allis Chalmers D10 Solenoid, 12 Volt
Solenoid, 12 Volt
- This is a 3 Post 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. For tractor models D10, D12, D14, D15, (D17, D19, 170, 180 with 1107695 starter) D21 all with gas engines and Delco starters. Replaces Delco DR1467, OEM 237136, 233296, 70237136, 910687. May come in a silver metal casing versus black plastic. (Part No: DR1467)
$16.23

Allis Chalmers D10 Solenoid, 6 Volt
Solenoid, 6 Volt
- Starter solenoid. For tractor models D10, D12, D14, D15 all with gas engines. (Part No: 581744)
$30.44

Allis Chalmers D10 Spark Plug
Spark Plug
- Replaces Autolite AL216, AL7, AL295 and Champion H8, H8J, H10, H11, H12, J8 spark plugs. 14mm thread diameter, 3/4" reach, 13/16" hex. (Part No: AL295)
$2.40

Allis Chalmers D10 Spark Plug Wire Set, Custom
Spark Plug Wire Set, Custom
- Fits: B, C, CA, D10, D12, D14, D15, D17, I40, I400, I500, I60, I600, IB, RC, WC, WD, WD45, WF, 170, 175, 510, 512, 514, 610, 612, 614 With Distributor Only. Replaces: 225084, 225613, 229867, 70225084, 70225613, 70229867 (Part No: S.65034)
$18.09

Allis Chalmers D10 Starter Drive
Starter Drive
- This starter drive gear assembly fits the following tractor models: D10, D12, D14, and D15 all 1961 and later that are using the Delco starters with the numbers matching: 1107265 and 1107758. (Part No: 70233295)
$51.75

Allis Chalmers D10 Starter Drive
Starter Drive
- For tractor models 6 volt 10 teeth D-12, D-14, WC, WD, WD45, WF, D-10 SN# <3501. Replaces 1859020, 1868804. (Part No: 74044454)
$38.04

Allis Chalmers D10 Starter Drive
Starter Drive
- Starter Drive - WC, WF, WD, WD45 (models using Delco 1107017 or 1107951) - D10, D12, D14 (models for 1957-1960 using Delco 107474 or 1107466). Replaces 1868804. (Part No: 565549)
$20.39

Allis Chalmers D10 Starter Drive Housing
Starter Drive Housing
- For tractor models B, IB, C, CA, RC, WC, WD, WD45, D10, D12, D14. All with Delco starters 1107466, 1107006, 1107017, 1107024, 110743, 1107044, 1107045, 1107046, 1107096 or 1107951. (Part No: 1879156)
$67.07

No
Picture
Starter Drive Spring
- Starter drive spring For B, C, CA, D10, D12, D14, WC, WD, WD45, WF Tisco has drive and springs for less money (Part No: 1860639)
$35.51

Allis Chalmers D10 Starter Drive, Improved Style
Starter Drive, Improved Style
- This improved style starter drive is a positive ratchet style. For models WC, WF, WD, WD45 using Delco starter 1107017 or 1107951. Also for models D10, D12 and D14 using Delco starter 107474 or 1107466. Replaces 1868804. Ten tooth drive, counter clockwise rotation, Barrel Folo rubber cushion drive design, 15.9mm inside diameter, 39.6mm gear diameter, 95-109mm. (Part No: 565549-New)
$19.43

Allis Chalmers D10 Tune Kit, Comprehensive
Tune Kit, Comprehensive
- This Comprehensive Tune Kit is for 4 cylinder gas engines. Includes spark plugs (autolite 295 or equivalent), points, condenser, rotor, distributor cap, and universal plug wire set. For AC tractors using CLIP-HELD Delco distributor and 14mm, 3/8 inch reach 13/16 inch hex spark plugs. Fits CA, WD, WD45, D10, D12, D14, D15, D17 except with Delco distributor number 112688. (Part No: ACTUNEKIT)
$42.57

Allis Chalmers D10 Tune Up Kit
Tune Up Kit
- for 4 Cylinder Gas Engines. Includes spark plugs(Autolite 295 or equivalent), points, condenser and rotor. For AC tractors using 14 mm, 3/8 inch reach, 13/16 inch hex spark plug. Fits CA, WD, WD45, D10, D12, D14, D15, D17 except with Delco Distributor number 112688. (Part No: ACTK1)
$23.06

Allis Chalmers D10 Voltage Regulator
Voltage Regulator
- 12-volt, using Delco generator 1100305 (VR1817). Also gas or diesel using Delco generators 1100345, 1100426. For D10, D12, D14, D15, D17, D19. The Three Post side of this regulator may be parallel or slightly splayed. Replaces Allis Chalmers Numbers; 229484, 236680, 70229484, 70236680 Delco Numbers; 1118381, 1118779, 1118977, 1118981, 1118987, 1118993, 1118997, 1118999, 1119191, 1119576 (Part No: 182548M92)
$16.88

Allis Chalmers D10 Voltage Regulator, 6 Volt, Positive Ground
Voltage Regulator, 6 Volt, Positive Ground
- For tractors using Delco generator 1100025 (VR1814). For D10, D12, D14. Replaces 70228365. (Part No: GDR6003)
$18.38



Allis Chalmers D10 Alternator Base Bracket Kit - Universal
Alternator Base Bracket Kit - Universal
- Universal Base Bracket Mounting Kit. For converting from a generator to an alternator. Contains: brackets, bolts, washers, nuts and basic instructions. (Part No: 2348258)
$33.75

Allis Chalmers D10 Alternator Conversion Plug
Alternator Conversion Plug
- Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style.. (Part No: ADR9209)
$12.71

Allis Chalmers D10 Alternator Conversion Plug
Alternator Conversion Plug
- Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Part No: ADR9209)
$12.71

Allis Chalmers D10 Alternator Top Adjusting Bracket, Universal
Alternator Top Adjusting Bracket, Universal
- Universal Top Adjusting Bracket For Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Part No: 8NL10302)
$11.93

No
Picture
Battery Hold Down
- Universal hold down for batteries that measure 8 15/16 inches long and 6 13/16 inches wide. (Part No: NCA10718A)
$16.55

No
Picture
Battery Hold Down
- Universal Battery Hold down. Verify your battery measurements. This will fit a 9 3/16 inches long and 7 3/16 inch wide battery. (Part No: 1111-0147)
$13.43

No
Picture
Battery Hold Down Bolts - PAIR
- These "J" bolts measure 10 1/2 inches long and are universal for many batteries. Verify length. Price is for a pair. (Part No: 393161R1)
$10.47

No
Picture
Battery Thermal Wrap
- This thermal battery wrap is used to keep your battery warm. It is 60 Watts and measures 28 inches long. (Part No: BTW28)
$22.50

No
Picture
Battery Thermal Wrap
- 80 Watt, 36 inches long wrap to keep your battery warm. (Part No: BTW36)
$37.48

No
Picture
Battery Thermal Wrap
- 160 Watt, 36 inches long wrap to keep your battery warm. (Part No: BTW72)
$53.81

No
Picture
Coil
- This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Part No: 28010)
$31.83

Allis Chalmers D10 Coil - Universal 12V
Coil - Universal 12V
- Universal coil fits many models. This Coil comes with an external resistor which can be removed if you need a coil with no resistance. Also comes with a mounting bracket. Coil is designed to be used on a 12 volt tractor system with the resistor or 6 volt system without the resistor. Replaces: 74061737, 74514967. (Part No: D5TE12029AB)
$7.13

Allis Chalmers D10 Coil Bracket
Coil Bracket
- Universal Coil Bracket (Part No: R1940)
$3.50

Allis Chalmers D10 Coil, High Performance (Black), 12 Volt, Epoxy Filled
Coil, High Performance (Black), 12 Volt, Epoxy Filled
- Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower Black, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 3.0 Ohms of resistance. (Part No: 40611)
$45.43

Allis Chalmers D10 Coil, High Performance (Black), 12 Volt, Oil Filled
Coil, High Performance (Black), 12 Volt, Oil Filled
- Pertronix Flame Thrower heavy duty, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 3.0 Ohms of resistance. (Part No: 40511)
$36.05

Allis Chalmers D10 Coil, High Performance (Black), 6 Volt, Epoxy Filled
Coil, High Performance (Black), 6 Volt, Epoxy Filled
- Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower Black, high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 1.5 Ohms of resistance. (Part No: 40111)
$45.43

Allis Chalmers D10 Coil, High Performance (Black), 6 Volt, Oil Filled
Coil, High Performance (Black), 6 Volt, Oil Filled
- Pertronix Flame Thrower high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Coil has 1.5 Ohms of resistance. (Part No: 40011)
$44.90

Allis Chalmers D10 Coil, High Performance (Chrome), 12 Volt, Epoxy Filled
Coil, High Performance (Chrome), 12 Volt, Epoxy Filled
- Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower Chrome, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 40601)
$45.43

Allis Chalmers D10 Coil, High Performance (Chrome), 12 Volt, Oil Filled
Coil, High Performance (Chrome), 12 Volt, Oil Filled
- 12-VOLT, Pertronix Flame Thrower Chrome, high performance coil is for all 12-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 3.0 Ohms of resistance. (Part No: 40501)
$40.51

Allis Chalmers D10 Coil, High Performance (Chrome), 6 Volt, Oil Filled
Coil, High Performance (Chrome), 6 Volt, Oil Filled
- 6-VOLT, Pertronix Flame Thrower Chrome, high performance coil is for all 6-volt systems. Delivers up to 40, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 1.5 Ohms resistance. (Part No: 40001)
$40.51

Allis Chalmers D10 Coil, Ultra High Performance (Black), Epoxy Filled
Coil, Ultra High Performance (Black), Epoxy Filled
- Epoxy filled coils provide superior winding support for high vibration environments. Pertronix Flame Thrower II Black, ultra high performance coil is for 12-volt systems. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 45111)
$50.16

Allis Chalmers D10 Coil, Ultra High Performance (Black), Oil Filled
Coil, Ultra High Performance (Black), Oil Filled
- Pertronix Flame Thrower II Black, ultra high performance coil is for 12-volt systems using "Ignitor II" electronic conversion kits or any 6 volt system. Delivers up to 45, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. (Part No: 45011)
$43.40

Allis Chalmers D10 Coil, Ultra High Performance (Chrome), Oil Filled
Coil, Ultra High Performance (Chrome), Oil Filled
- Pertronix Flame Thrower II Chrome, ultra high performance coil is for 12-volt systems using "Ignitor II" electronic conversion kitsor or any 6 volt system using the "Ignitor II". Delivers up to 45, 000 volts. Oil filled for better cooling and voltage insulation. Enables larger plug gap for greater fuel efficiency and more power. Fits existing brackets. Coil has 0.6 Ohms of resistance. For use with Ignitor II Electronic Ignition Module. (Part No: 45001)
$44.66

Allis Chalmers D10 Magneto, Wico XH & XHD, Service & Parts Manual
Magneto, Wico XH & XHD, Service & Parts Manual
- Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Part No: MAG6)
$14.25

No
Picture
Spark Plug
- Extended tip, 14mm thread, 3/4 inch reach. Replaces Champion N12YC. NOTE: Verify spark plug type before ordering. (Part No: AL65)
$2.73

No
Picture
Spark Plug
- Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Part No: AL85)
$2.73

Allis Chalmers D10 Spark Plug Wire Set, 4 Cylinder, Univeral
Spark Plug Wire Set, 4 Cylinder, Univeral
- Universal Spark Plug Wire Set, 4 Cylinder, straight boot, cut to length. (Part No: S2097)
$12.75

Allis Chalmers D10 Spark Plug Wire Set, 4 Cylinder, Universal
Spark Plug Wire Set, 4 Cylinder, Universal
- This Universal spark plug wire set can be used with the Ignitor high performance electronic ignition conversion kits. Kit has 90 degree sparkplug boots and straight distributor boots. (Part No: CPN12259)
$12.92

Allis Chalmers D10 Spark Plug Wire Set, Universal 6 Cylinder
Spark Plug Wire Set, Universal 6 Cylinder
- Universal Spark Plug Wire Set, 6 Cylinder, 90 degree boot, cut to length, brass terminals, copper strand core. Longest Reach is 33 inches. (Part No: SWS260)
$15.00

Allis Chalmers D10 Spark Plug Wire Set, Universal, 4 Cyl.
Spark Plug Wire Set, Universal, 4 Cyl.
- Universal Spark Plug Wire Set, 4 Cylinder, 90 degree boot, cut to length. Longest Reach is 33 inches. Solid brass distributor coils, Zinc-coated plug terminals, tin-coated copper core, boots constructed from EPDM rubber and dual-jacket insulation. Meets SAE J2031 Specifications. Made in the USA. (Part No: CPN12259)
$12.92

Allis Chalmers D10 Starter, Generator, Distributor Tag, 6 Volt, Blank
Starter, Generator, Distributor Tag, 6 Volt, Blank
- Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Part No: DELCO6)
$14.55

Allis Chalmers D10 Stripper and Crimping Tool
Stripper and Crimping Tool
- Professional Fast and Easy tool for stripping and crimping electrical wires. (Part No: B1SB6718)
$24.30

Allis Chalmers D10 Tag for Starter\Generator, 12 Volt, Blank
Tag for Starter/Generator, 12 Volt, Blank
- Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Part No: DELCO12)
$14.45

Allis Chalmers D10 Terminal Kit
Terminal Kit
- Deluxe solderless terminal and connector assortment. 175 pieces. Includes female slip ons, oval butt connectors, ring connectors, male slip ons, spade terminals, and wire splice. (Part No: B1SB22)
$34.19

Call 800-853-2651 to Order
Or Click the "Add to Cart" Button

Category: Electrical System

[Categories]   [All D10 Parts]   [All Allis Chalmers Models]  







PayPal


Order Toll Free
(800) 853-2651
(Mon-Fri)


Order online
anytime!



  

YESTERDAY's TRACTORS has been a leading tractor parts supplier on the internet since 1995. Join thousands of happy customers who have purchased parts and more for their antique tractor from us!

Copyright © 1997-2019 Yesterday's Tractor Co.
Antique Tractor Headquarters
All Rights Reserved

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Website Accessibility Policy