International Harvester / Farmall Super MDV Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Actuating Spring - Used with disc brakes. For tractor models (M from serial number 294226 and up), (MD from serial number 285505 and up), Super M, Super MTA, Super MV, Super MDV, Super W6, Super W6TA, Super WD6, OS6, ODS6, 400, 450, W400, W450, 560, 656, 660, 664, 666, 686, Hydro 70, Hydro 86. Replaces A30897, A41816. Replaces 357116R1, 619731C1, 72504717V. Priced each. Measures 1.209 inches overall length, .761 inches outside diameter with a wire diameter of .105 inch. (Item #: 113798, Ref: A155624) $1.70
Disc Brake Ball Bearing - Measuring 7/8 inches, this ball bearing is used in many disc brake systems. Typically 4 or 6 used per wheel. Replaces OEM numbers 09384AB, 150734A1, 16028R1, 166264, 16779X, 17028R1, 20063060, 2073622, 211-1028, 211-1328, 211-19, 211-221, 31-1750393, 33-0026328, 50A4272, 706039R1, 706039R2, 72073622, 7A2606, 0166264, 81716998, 81847078, 81866502, 82979987, 87554519, 87672308, 9170150, 920095936, 9959976, 9960587, BDB78, D5NN2N141A, E94FB9, E9NN2N324AA, E9NN2N324AB, GM145662, K963645, M830T, O9384AB (Item #: 126209, Ref: M830T) $2.30
Disc Brake Boot - This Boot is used on Tractors with Disc Brakes. Used on Farmall MTA, ODS6, OS6, Super M, Super MD, Super MDV, Super MV, Super W6, Super W6TA, Super WD6, 400, 450. Replaces 357044R1 (Item #: 112347, Ref: 357044R1) $6.60

Cooling System
Water Block Drain Plug, Winged - Plug 3/8 inch pipe thread, has "IH" and part number stamped in it, cast iron with zinc plating. For tractor models A, AV, Super A, Super AV, Super A1, Super AV1, B, BN, C, H, HV, Super H, Super HV, I4, I6, ID6, I9, ID9, M, MD, MV, MDV, Super M, Super MD, Super MV, Super MDV, MTA, 04, 0S4, 06, 0S6, ODS6, T6, T340, TD6, T9, TD9, W400, W450, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650 (Gas/Diesel), serviceable for Cub, Cub Lo-Boy. (Item #: 178066, Ref: 45314DC) $13.00

Drive Train
Axle Seal, Rear - For 2-3/4 inch axles (inside diameter 2-3/4 inch, outside diameter 3-5/8 inch). For tractor models 200, 230, 240, 2504, 2544, 2656, 340, 400, 404, 450, 460, 504, 544, 560, 656, 666, Hydro 70, Hydro 86, M, Super M, Super MD, Super MV, Super MDV, Super MTAD, Super MTA. All with 2-3/4 inch axle diameter. Replaces 117567H1, 154935H1, 165651H1, 167175H1, 333750R91, 358780R91, 358819R91, 360457R91, 369319R91, 377788R1, 377788R91, 381042R91, 48776D, 57085D, A27130, AA510R, AA520R, O7041AB (Item #: 172589, Ref: 377788R1) $17.00
Gear Shift Boot - Some of the Farmall / International tractors were not factory equipped with a gear shift boot, and it was sold as an extra. This boot is used on models: H, M, 560, I4, I6, ID6, Super MVTA, 2606, HV, MD, T340, T5, MDV, MV, TD6, O4, O6, ODS6, OS4, OS6, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MTA, Super MV, Super W4, Super W6, Super WD6, W4, W6, WD6, 300, 330, 340, 350, 400, 404, 424, 444, 450, 460, 504, 606, 660, B275, 354, 384. It measures 4-3/4 inches tall, 11/16 inch top hole inside diameter and 2-3/4 inches bottom hole. (Item #: 182890, Ref: 64603DA) $24.80
Oil Seal - Fits: [A, A-I, A1, AV, AV-1, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 2404, 404 (Top Transmission Shaft Front Seal)], [B-250, B-275, B-276, B-414, 2300, 2300A, 2424, 2444, 3414, 3444, 354, 364, 384, 424, 434, 444 (Bull Pinion Shaft Bearing Retainer Seal)], [Cub, Cub Lo-Boy, 154, 184, 185 (Final Drive Upper Pinion Shaft Seal)], [M, MD, MDV, MV (Transmission Counter Shaft Front Seal)], MTA (Front Wheel Seal; with single front 900 x 10 wheel), [O4, OS4 (PTO Output Shaft Seal; serial number 2159 to 9300)], [Super M, Super MD, Super MDV, Super MV (Transmission Counter Shaft Front Seal; up to serial number F52627 and up to serial number L51241)], W4 (PTO Output Shaft Seal; serial number 786 to 9300). Replaces: 21969D, 264694R91, 287440R91, 3043788R91, 3043788R92, 358765R91, 358784R91, 358808R91, 358823R91, 381907R91, 42177D, 43278D, 50839D, 530969R91, 703907R91, 703908R92, A29424. (Item #: 178204, Ref: 381907R91) $6.00
Reverse Idler Gear Bushing - This Bushing Measures 1.245 inches inside diameter, 1.375 inches outside diameter, 1.486 inches long. Sold individually. This bushing has a superior dimpled brass inner design to retain grease. No need for an external grease hole. Note: Must be honed or reamed to size when installed. Used on the following as a reverse idler gear bushing: 400, 450, 560, 660, B-450, BM, BMD, M, MD, MDV, MTA, MV, O6, ODS6, SBM, SBMD, Super M, Super MDTA, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super W6, Super WD6, W400, W450, W6, W6TA, WD6, WD6TA; Replaces: 48841D (Item #: 109669, Ref: 48841D) $13.70

Electrical System
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, Cub 154 Lo-Boy, Cub 184 Lo-Boy, Cub 185 Lo-Boy, H, HV, I4, I6, I9, ID9, ID6, M, MD, MDV, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD-TA, Super MDV, Super MTA, Super MV, Super W4, Super W6. R6332 (Item #: 124839, Ref: 107304C91) $115.00
Distributor Cap - Distributor cap for 4 cylinder models using a Delco distributor with a clip held cap. Replaces 811735 Delco and 1750411M1. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414. (Item #: 104554, Ref: 1750411M91) $9.10
Distributor Gear - This Distributor Gear has 32 teeth. It is used on IH Distributor 353898R11. Replaces original part numbers 353902R1, 531461R91 (Item #: 111179, Ref: 353902R1) $30.00
Electronic Ignition Conversion Kit - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 6 volt POSITIVE ground system only. Use with distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650 (Item #: 105084, Ref: 1442P6) $157.00
Electronic Ignition Conversion Kit - Electronic Module Replaces Points and Condenser. Use on tractors with 12 volt Positve Ground System only. (FOR NEGATIVE GROUND order part number 1442). Use with distributor number 357935R91 or 353898R1 on models: B, Cub, cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650. (Item #: 105085, Ref: 1442P12) $174.00
Electronic Ignition Conversion Kit - 12v Negative Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt NEGATIVE ground system only. Distributors with clip type cap. (Item #: 105071, Ref: 1142) $137.00
Electronic Ignition Conversion Kit - 12V Negative Ground - Pertronix Electronic Ignition Module Replaces Points and Condenser. Use on tractors with 12 volt NEGATIVE ground system only. Use with IH distributor 353898R1 or 357935R91 on: Cub, Cub Lo-Boy, Cub 154 Lo-Boy, 184, Cub 185 Lo-Boy, A, AV, Super A, Super AV, BN, C, Super C, H, HV, Super H, Super HV, M, MV, Super M, Super MTA, Super MD, Super MDV, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 404, 424, 444, 454, 504, 600, 650. Verify distributor number before ordering. (Item #: 105083, Ref: 1442) $157.00
Electronic Ignition Conversion Kit - 12v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with distributor part no. 1885368 or 1111411. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 12 volt POSITIVE ground system only. (Item #: 108148, Ref: 1142P12) $174.00
Electronic Ignition Conversion Kit, 6v Positive Ground - For Tractor Models: A, AV, Super A and AV, B, BN, C Super C, H, HV, Super H and HV, M, MV, Super M and MTA, Super MD and MDV, W4, Super W4, W6, Super W6, W9, Super W9, 354, B414, all with Delco distributor part no. 1885368 with clip type cap. Electronic ignition conversion kit replaces points and condenser with an electronic module. Use on 6 volt positive ground system only. (Item #: 105072, Ref: 1142P6) $164.00
H4 Magneto Pinion Driven Gear - This gear has 24 teeth and measures: 0.380 inch inside diameter, 0.759 inch outside diameter, 1.075 inch gear outside diameter, 0.952 inch overall height. It is used on H4 Magnetos. (Item #: 183878, Ref: 49420DX) $27.10
Ignition Tune-up Kit, Basic, Delco Clip Held Cap - Ignition kit For Delco ONLY distributor with CLIP held cap. VERIFY DISTRIBUTOR NUMBER TO ENSURE FIT. Contains points, condenser, and rotor. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414, I4, I6, MTA, MV, O4, O6, T6, U2, W4, W6. For Delco distributor numbers 1111716, 1112583, 1112589, 1112557, 1112570, 1112585, 1111722, 1111737, 1112583. Not for IH Distributors. (Item #: 103151, Ref: ATK1DCR) $10.30
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.80
Spark Plug Wire Set, Custom - IH or Delco Distributors and Magnetos. For the following models with 90 degree angle boots: A, I4, AV, Super A, Super A1, Super AV, SuperAV1, B, BN, C, Super C, Cub, Cub Lo-Boy, 154, 184, 185, H, HV, Super H, Super HV, M, MD, Super M, Super MD, Super MDV, MDV, Super MDVTA, MTA, Super MTA, MV, Super MV, Super MVTA, O4, O6, ODS6, OS4, OS6, T340, T5, T6, TD6, SuperW4, W4, Super W6, Super W6TA, W6, W6TA, Super WD6, WD6, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404, 424, 444, 450, W450, 504. Replaces the following OEMS: 352947R91, 352951R91, 352954R91, 352956R91, 356687R92, 356689R92, 356691R91, 356694R92, 356695R92, 356697R93, 362439R91, 362789R91, 407487R1, 45327DA, 46277DA, 50075D, 52794D, 65352D, 65357D, 65358D, and 65359D. (Item #: 120100, Ref: S.67475) $17.50
Starter Drive Housing - This Starter Nose Cone is used on Delco starter numbers 1107021, 1107060, 1107067, 1107093, 1107174, 1107427, 1107448, 1108096. Bushing is included. This part replaces Delco part numbers 1878661, 1887109, 1910093, 1943759 (Item #: 179382, Ref: 1878661) $75.01
Starter Switch Actuator - This new foot starter switch actuator lever and bracket fits; H, HV, M, MD, MDV, MV, Super H, Super HV, Super M, Super MD, Super MDV and Super MV where a foot activated starter switch mounts to the steering post. Replaces: Lever: 351922R11, Bracket: 351924R1 (Item #: 185010, Ref: IHS3263) $57.14
Tune-up Kit - This Tune-up Kit is for Delco Distributors with clip help cap. 4 Cylinder kit includes Autolite spark plugs (Replaces Autolite AL386, AL388, AL3116 and Champion D10, D14, D16, RD16, D21, D23 plugs), points, condenser, and rotor. For tractor models with clip held Type Delco Distributor Caps. For tractor models A, AV, Super A, Super AV, B, BN, C, Super C, H, HV, Super H, Super HV, M, MD, Super M, Super MTA, Super MD, Super MDV, 4, Super 4, 6, Super 6, 9, Super 9, 354, B414. Verify correct spark plug replacement. Note, not for British Delco Distributors 7953342. (Item #: 173738, Ref: MFITK10) $27.30
No Picture Wiring Harness - Wiring harness, switch to rear light. For M, MD, MV, Super MD, Super MDV. Restoration Quality. (Item #: 358121R91) $67.62

Fuel System / Air Intake
Carburetor Drain Trough - This Carburetor Drain Trough is used on tractors with F8 starting diesel carburetors. Replaces 58843DX. (Item #: 180176, Ref: 58843DX) $70.00
Carburetor Float Valve Assembly - This is a new Carburetor Float Valve Assembly with stainless steel needle. It us used on F8 Diesel Starting Carburetors (53873DH, 67860DCM). (Item #: 179312, Ref: 32581DXB) $69.94
Carburetor Fuel Line Fitting With Strainer - Fits INTERNATIONAL carburetors: 356948R92, 35865R91, 366066R91, 367258R92, 367259R92, 372723R92, 378196R94, 379813R91, 380956R91, 381984R91, 388297R92, 388424R92, 388425R96, 390082R92, 396197R93, 45108DB, 45108DC, 50981DA, 50981DB, 50983DB, 52714D, 52814DA, 52815D, 52815DA, 533622R91, 53873DF, 53873DH, 539575R91, 56543DE, 60329DA. 1/4 inch pipe to 5/16 inch flare. (Item #: 111514, Ref: 29902DX) $16.50
Carburetor Gasket Set - This Gasket Set is used on F8 Diesel Starting Carburetors (53873DH, 67860DCM). Contains 32606DD, 53459DA (Item #: 160212, Ref: IHS997) $16.30
Fuel Cap - 1 15/16 inch overall outside diameter fits many: 240, 300, 350, 400, 450, 600, 650, H, HV, M, MD, MDV, O4, O6, ODS6, OS4, OS6, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super W6, Super WD6, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S. (Item #: 116503, Ref: 40756D) $8.50
Fuel Cap, Top Vented - 2-11/16 inch inside diameter, 1.500 inch height (including splash guard) and 1.118 inch height cap only. Says "Buy Clean Fuel Keep it Clean". For tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy (WILL NOT FIT 154, 184, 185), F12, F14, F20, F30, H, HV, I4, I6, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MV, Super W4, Super W6, Super WD9, Super WDR9, T4, T5, T6, T9, TD14, TD14A, TD15, TD18, TD18A, TD20, TD6, TD9. (Item #: 121475, Ref: 12770D) $13.00
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. Replaces: 13194D, 25854, 49923D (Item #: 105364, Ref: 49923D) $3.50

Gauges
Fuel Gauge Cap - This vented fuel cap has a built in gauge. Overall length is 14 3/4 inches. Uses gasket part number 23977DA - sold separately. For models I6, M, MD, MDV, MV, O6, Super M, Super MD, Super MDV, Super MTA (Diesel), Super MV, Super W6, Super WD6, W6, WD6. (Item #: 160451, Ref: 365499R91) $107.00
No Picture Fuel Gauge Cap Gasket - Gasket fits our Fuel Gauge Cap part numbers 365498R91, 365495R91 and 365499R91. (Item #: 110635, Ref: 43984D) $3.00

Hydraulic System
Hydraulic Auxiliary Control Valve Rod - Hydraulic Auxiliary Control Valve Control Rod is 43-1/2 inches long with a 3/8 inch diameter. It fits the following tractors with optional live hydraulics and auxiliary control valve: M, MD, MDV, MTA, MV, Super M, Super MD, Super MDV, Super MDV-TA, Super MTA, Super MV, Super MVTA, Super MTA. It replaces original part number 359479R91 (Item #: 179699, Ref: 359479R91) $45.50
Hydraulic Dipstick - Mounts inside the hydraulic pump breather fill pipe, 11.80 inches long. For tractor models H, HV, M, MV, MD, MDV, Super H, Super HV, Super M, Super MV, Super MD, Super MDV, 140 Combine and 120 Windrower. All equipped with lift all countershaft driven hydraulic pump. (Item #: 126480, Ref: 15158EX) $32.50
Hydraulic Pump Control Rod - Hydraulic Pump Control Rod is used on the following tractors with belly mounted hydraulic pumps: M, MD, MDV, MV, Super M, Super MD, Super MDV, Super MV. The length of this rod is 39-3/4 inches long with a 3/8 inch diameter. It replaces original part number 15092EX (Item #: 179211, Ref: 15092EX) $48.80
Hydraulic Pump Control Rod - Hydraulic Pump Control Rod is 22-1/4 inches long with a 3/8 inch diameter. One end is 3/8 inch -16 UNC threads. It is used on the following tractors with live hydraulic pump and reservoir mounted under the fuel tank: MTA, Super M, Super MD, Super MDTA, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA. It replaces original part number 358458R11. (Item #: 179701, Ref: 358458R11) $48.80
Seal, Countershaft Driven Hydraulic Pump - This Seal is used as a countershaft driven hydraulic pump seal or a hydro charge pump seal on Farmall / International: H, M, HV, MD, MDV, MV, Super H, Super HV, Super M, Super MD, Super MDV, Hydro 86, Super MV, 544, 656, 666, 2544. It measures 1.375 inch inside diameter, 2.130 inch outside diameter, and 0.437 inch wide. Replaces 0511073, 1K1590, 1K1590, 224810, 230608, 241779, 340214, 35451D, 357970R91, 357976R91, 380184R91, 43509D, 43509DA, 511073, 527829R91, 60454D, 659124R91, 70224810, 70230608, 70241779, 70241D, 938294R91, 938294R92, AH14076, AL2094T, AL56820, AM253T, AN30648, AN32717, AP24021, K1590, K1590, M86688, N71730N, T22069 (Item #: 128541, Ref: 70241779) $7.30

Lights
Headlight Assembly, Flat Back, 12 Volt - For Farmall Cub, Cub Lo-Boy, C, Super C After 159455, M, MV, MD, MDV, MTA, Super MD, Super MDV. Also for Model 100, 130, 140, 200, 230, 240, 300, 350 Utility, 330, 340, 400, 450. Replaces OEM# 357884R94. Flat-Back (not teardrop) Primered red. Price is for one complete headlamp assembly. (Item #: 105334, Ref: 357884R91-12V) $47.60
Headlight Assembly, Flat Back - 6 Volt - For Farmall Cub, Cub Lo-Boy, C, Super C after serial number 159455, M, MV, MD, MDV, MTA, Super MD, Super MDV, also for Model 100, 130, 140, 200, 230, 240, 300, 350 Utility, 330, 340, 400, 450. Replaces OEM number 357884R94. Flat-Back (not teardrop). Primered red. Price is for one complete headlamp assembly. (Item #: 105333, Ref: 357884R91-6V) $41.50
No Picture Headlight Lens - For tractor models 100, 130, 140, 200, 230, 240, 300, 350, Farmall 300, 350 Utility, 330, 340, IH and Utility 240, 400, 450, Farmall Cub, Cub Lo-Boy, Farmall C, M, MV, MD, MDV, Super MD, Super MDV. (Item #: 179183, Ref: 357884R94) $14.40
Light Switch, 12 Volt - 4 position with Old style knob, replaces cut out switch when converted to regulator. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 125672, Ref: R5362) $55.00
Light Switch, 12 Volt - 3 position with Old style knob, with regulator only. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 107984, Ref: R5364) $40.50
Light Switch, 12 Volt - 4 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 178354, Ref: R5366) $49.40
Light Switch, 12 Volt - 3 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 107095, Ref: R5368) $38.70
Light Switch, 6 Volt - 4 position with Old style knob, replaces cut out switch when converted to regulator. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 178387, Ref: R5361) $49.40
Light Switch, 6 Volt - 3 position with Old style knob, with regulator only. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 125715, Ref: R5363) $52.87
Light Switch, 6 Volt - 4 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 178351, Ref: R5365) $37.00
No Picture Light Switch, 6 Volt - 3 position with new style knob. For tractor models A, AV, B, BN, C, Cub, Super A, Super AV, Super C, H, HV, M, MD, MV, MDV, Super H, Super HV, Super M, Super MD, Super MDV, Super MTA, Super MV, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, W4, W6, W9, Super W6, Super W6TA, Super W4, WD6, WD9, WR9, WDR9, O4, OS4, O6, OS6, I4, ID6, I9, ID9. (Item #: 107094, Ref: R5367) $27.70
Light Switch Knob - Old style for rotary light switches. For tractor models A, AV, B, BN, C, H, HV, M, MD, MV, MDV, W4, W6, W9, WD6, WD9, WR9, WDR9, O4, OS4, I4, I6, I9, ID6, ID9, Super A, Super AV, Super C, Super H, Super HV, Super M, Super MD, Super MV, Super MDV, Super MTA, Super W4, Super W6, Super W6TA, 100, 130, 140, 200, 230, 240, 300, 350, 400, 450, W400, W450, Cub. (Item #: 179711, Ref: 57313D) $11.10

Seats
Seat Locator Spring - This Seat Locator Spring fits: C, Super C, (Super H, Super HV serial number 19234 and up), (Super M, Super MD, Super MDV, Super MTA, Super MV serial number 28175 and up) Super MTA (Diesel serial number 28175 and up), 200, 230, 400, 450, 560, 600, 650, 660, Farmall Rowcrop: 300, 350, 460, Wheatland: 400, 450; Replaces: 352105R1. (Item #: 115150, Ref: 352105R1) $8.50
Seat Shock Bushing - This bushing is for the horizontal bolt hole. It measures 1.223 inches outside diameter at the largest point. The hole inside diameter is 0.597 inches. The length measures 0.724 inches overall. 2 to 4 used per shock. This part replaces 72696R1, 70222488, T19118, 230288, 250416R1, F3296R, R26832, 760674M1 (Item #: 109602, Ref: 72696R1) $2.30
Seat Shock, Mid Mount - For tractor models: C, Super C, Super H, and Super H. All serial number 19234 and up; M, MD, MDV, Super MDV, Super MD, 200, 230, 300, 350, 400, 450, 460, 560. Shock absorber for mid mounted shock is 7 1/4 inches from center-to-center compressed length. Replaces IHS347, 361033R91. (Item #: 105340, Ref: 351750R93) $36.40
Seat Shocks - Rear Mount - For H and HV with serial number 15698 to 281555; M, MD, MDV, Super MD and Super MDV with serial number 9287 to 165270. Rear Mount Seat Shocks are 11 1/2 inch center to center compressed length. Replaces IHS329. (Item #: 105339, Ref: 352587R92) $33.40
Seat Support Pivot Rod - Rod that fits in the end of the Seat Support. OTHER PARTS IN PICTURE SHOWN FOR REFERENCE ONLY. (Item #: 105344, Ref: 352648R1) $23.30

Steering
Steering Shaft Cross and Bearing (U-Joint) - Tighten up your steering with a new Universal Joint. This part measures 2.305 inches across cap to cap, with a 0.968 inch cap diameter. Some models use more than one, sold individually. Some models used different sizes, verify measurements. Replaces OEM numbers 10P715, 1KAR758, 224890, 350254R91, 357439R91, 363313R91, 363321R91, 52977DAX, 70224890, 836514M91, 841193M92, A20435, A20684, A30408, A30425, A30428, A30435, VTA3227, Z862 (Item #: 115351, Ref: 70224890) $11.00
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00
Steering Worm Gear, Sector - 32 teeth. For tractor models 400, 450, M, Super M, Super MTA. The style of this gear is full circle. This gear has 32 teeth. It can also replace a 19 tooth sector (1/2 inch moon style). Replaces: 50037DA, 50037DB, 704168R1. (Item #: 124445, Ref: 50037DB) $171.42
Steering Worm Shaft Oil Seal - This Steering Worm Shaft Oil Seal measures 1.000 inch inside diameter, 1.503 inch outside diameter, 0.250 inch wide. Fits B, BN, C, H, HV, M, MD, MDV, MV, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDV-TA, Super MV, Super MVTA, 200, 230, 240, 400, 450, MTA diesel, 300, 340, 350. Replaces: 359042R91, 359257R91, 364468R91, 43800D, 43800DA, 488561R91. (Item #: 122678, Ref: 43800D) $5.80

Wheels
No Picture Bearing Cone - Outer cone for bearing kit FW112FS. For tractor models HV, Super HV, MV and MDV, O6, ODS6, W6, WD6, Super W6 and WD6, 400, 450. For 400, 450, HV, MDV, MV, O6, ODS6, Super HV, Super MDV, Super MV, Super W6, Super WD6, W6, WD6. (Item #: ST771A) $69.39
No Picture Bearing Cone - Inner cone for bearing kit FW112FS. For tractors HV, Super HV, MV and MDV, O6, ODS6, W6, WD6, Super W6 and WD6, 400, 450. For 400, 450, HV, MDV, MV, O6, ODS6, Super HV, Super MDV, Super MV, Super W6, Super WD6, W6, WD6 (Item #: 172820, Ref: ST781A) $40.90
No Picture Bearing Cup - Inner cup for bearing kit FW112FS. For tractors HV, Super HV, MV and MDV, O6, ODS6, W6, WD6, Super W6 and WD6, 400, 450. For 400, 450, HV, MDV, MV, O6, ODS6, Super HV, Super MDV, Super MV, Super W6, Super WD6, W6, WD6 (Item #: 179997, Ref: ST882) $13.50
Front Wheel Bearing Kit - Kit contains one each: 342S (cone), 332 (cup), 2878 (cone), 2820 (cup), 48704DA (seal), 15288A (felt seal). Repairs one wheel. For 400, 450, HV, MDV, MV, O6, ODS6, Super HV, Super MDV, Super MV, Super W6, Super WD6, W6, WD6. (Item #: 126828, Ref: FW112FS) $179.00
Oil Seal - Oil seal for bearing kit FW112FS. For tractor models HV, Super HV, MV and MDV, O6, ODS6, W6, WD6, Super W6 and WD6, 400, 450. 358779R91, 358818R91, 367161R91, 372475R91, 48704D, 48704DA, 704108R91, 708108R91 (Item #: 123838, Ref: 48704DA) $30.58
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.80
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.40
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.40
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $5.00
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.90
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.80
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.50
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.90
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $5.00
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.20
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.50
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.60
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.40
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.80
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.20
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.50
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.40
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.40
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.60
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.80
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.00
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.50
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.50

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98
No Picture Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $19.20
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.20
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $25.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.08
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $12.90
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $30.10
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $49.57
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $364.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $364.00
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $439.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $439.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.17
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90
Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $43.10
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.80
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.50
Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $46.30
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60
Work Light 12V - Universal Work light is 12 volt, 3000 candle power, and a trapezoidal light pattern. I does swivel up and down, not side-to-side. Comes with 4-1/2" diameter sealed beam lamp, part number L4411. Does not have a switch on the back. (Item #: 173803, Ref: L408-12V) $38.40

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $389.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $123.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.00
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $55.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.60
No Picture Paint, Farmall Red, Spray Can - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP110SP) $8.50
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.30
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $24.00
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $8.60
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $24.00
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $90.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.00
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $11.00
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $62.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $24.90
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $8.20
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $24.00
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $8.50
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01

PTO / Driveline
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor and implement yokes. 1-3/8 inch 6 spline Q.D. tractor yoke. 1-3/8 inch round bore with 1/2 inch pin hole implement yoke. 1300 mm (51 inch) overall length end of yoke to end of yoke. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit, 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch) overall length (43-3/4 inch). Verify length before ordering. (Item #: 180775, Ref: AB4111WY) $174.00
Driveline Assembly with Yokes - AB4 series, complete drive shaft assembly with shielding and tractor yoke, ratcheting torque limiter on implement end. 1-3/8 inch 6 spline Q.D. tractor yoke, 1-3/8 inch 6 spline ratcheting torque limiter with quick disconnect on implement end. 1372 mm (54 inch) overall length end of yoke to end of clutch. 1110 mm (43-3/4 inch) compressed length center to center of cross bore. Cross and bearing kit 27 mm 1.063 (1-1/16 inch) bearing diameter x 74.6 mm 2.940 (2-15/16 inch). 1372 mm (54 inch) overall length ***VERIFY LENGTH BEFORE ORDERING*** (Item #: 124815, Ref: AB4111K33) $339.00
NOTE PTO Adapter - PTO adapters are located under the PTO category in the Accessories and Universal Parts section.	NOTE
PTO Safety Clutch, 40 HP - 1-3/8 inch 6 spline male and female ends, 6 inch diameter, 40 horse power capacity. Heavy duty unit allows PTO driven implements to freewheel with adjustable safety protection under load. Prevents expensive damage to internal tractor PTO packs. Prevents single clutch tractors from being driven forward by PTO over-run. (Item #: 183648, Ref: B9164) $268.00