International Harvester / Farmall Super AV1 Tractor Parts

[Categories]   [All Farmall Models]   [Print]  

Brakes
Brake Pedal Shaft, LH - Fits A, AV, B, BN, Super A, Super AV, Super AV1, Super A1, 100, 130, 140. (Item #: 153603, Ref: 51425DX) $171.87
Brake Pedal Shaft, RH - This brake pedal shaft is the right hand side. It is for models A, AV, B, BN, Super A, Super AV, Super AV1, Super A1, 100, 130, 140. (Item #: 153602, Ref: 51507D) $167.00
Final Drive Gasket Kit - This 4 piece Final Drive Gasket Kit Includes (1) rear axle housing oil pan gasket, (2) rear axle outer bearing retainer gaskets, (1) rear axle housing inner bearing cap gasket. 2 used per tractor, sold individually. Fits: A, AV, B, BN, Super A, Super A1, Super AV, Super AV1; Replaces: 43245D, 47954D, 48009D, 48009DB (Item #: 182489, Ref: 43245D) $21.70

Cooling System
Fan Assembly - For tractor models A, Super A serial number 250001-317191, Super AV, Super A1, Super AV-1 (ALL A and Super A series between serial number 250001 and 317191), B, C, Super C. Fan measures 15 5/8 inches, pulleys measure 3 3/4 inch and 3 1/4 inch diameter. Replaces OEM number 701360R91, 131489C91, 70136D, 70212D. (Item #: 100772, Ref: 701360R) $80.00
Fan Pulley Assembly, Late - This pulley assembly fits Cub and Cub Lo-Boy C-60 engine serial number 165153 and up, Super A with C-113 engine serial number 317192 and up, Super AV and Super AV1 with C-123 engine, Super AV1 with C-113 engine serial number 317192 and up, Super C with C-123 engine, 100 and 130 with C-123 engine, (200, 230 and 240 with C-123 engine below serial number 65000). Fan mounting bolt thread is 12-24 UNC, 3.125 inch bolt pattern. Shaft is 5/8 inch -18 Thread. 4.379 inch outside diameter rear pulley. 4.062 inch outside diameter front pulley. VERIFY MEASUREMENTS. Will not fit 154, 184 or 185. (Item #: 126187, Ref: 131486C91) $144.00
Radiator - For tractor models Super A, Super A1, Super AV, Super AV1, Super C, 100, 130, 200 and 230. This radiator is for PRESSURIZED systems only. Inlet = 2-1/2". Outlet = 2". The core is 16-1/8 inches high and 16 inches wide. NOT FOR EARLY TRACTORS THAT DID NOT HAVE A WATER PUMP. Replaces 356356R96, 358104R93 (Item #: 101710, Ref: 356356R94) $400.00
Radiator - This Radiator fits all A, B and BN models as well as Super AV and Super AV-1. It will fit older non-pressurized systems and is close to, but not exactly like original. For original non-pressurized, see part number 58124DBX. If using this radiator to replaces an older non-pressurized radiator, you will also need to replace the cap with part number RW0021-9 (4 lb cap). If replacing the cap for a pressurized system use cap part number 825702M2 (7 lb cap). Core Height 15 7/8 inches, Core Width 16 inches, Depth 2 inches. Replaces original part numbers 358105R91, 58124DBX (Will need new cap). (Item #: 101706, Ref: 358105R91) $420.00
Radiator - This radiator is for the early models without water pump. Has 2 Inch Inlet and Outlet Tubes. Fits A and AV after serial number 41330, B and BN after serial number 40193, (Super A, Super AV, Super AV-I, all to serial number 355669) all without water pump. Has 2 inch inlet and outlet tubes. Core size is 17 3/8 inches wide X 16 1/2 inches high. Does not come with a cap. Uses Radiator Cap part number 43983D. (Item #: 125004, Ref: 58124DBX) $459.00
Radiator Cap - This is a 4lb Radiator Cap used with 358105R91 when replacing a non-pressurized radiator. (Item #: 178173, Ref: RW0021-9) $8.20
Radiator Cap - This is a 7 pound Radiator Cap used with 358105R91 for a pressurized system. Replaces: 361705R91, 362323R91. (Item #: 169633, Ref: 825702M2) $11.70
Water Block Drain Plug, Winged - Plug 3/8 inch pipe thread, has "IH" and part number stamped in it, cast iron with zinc plating. For tractor models A, AV, Super A, Super AV, Super A1, Super AV1, B, BN, C, H, HV, Super H, Super HV, I4, I6, ID6, I9, ID9, M, MD, MV, MDV, Super M, Super MD, Super MV, Super MDV, MTA, 04, 0S4, 06, 0S6, ODS6, T6, T340, TD6, T9, TD9, W400, W450, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, 450, 600, 650 (Gas/Diesel), serviceable for Cub, Cub Lo-Boy. (Item #: 178066, Ref: 45314DC) $13.00

Drive Train
Final Drive Gasket Kit - This 4 piece Final Drive Gasket Kit Includes (1) rear axle housing oil pan gasket, (2) rear axle outer bearing retainer gaskets, (1) rear axle housing inner bearing cap gasket. 2 used per tractor, sold individually. Fits: A, AV, B, BN, Super A, Super A1, Super AV, Super AV1; Replaces: 43245D, 47954D, 48009D, 48009DB (Item #: 182489, Ref: 43245D) $21.70
Oil Seal - Fits: [A, A-I, A1, AV, AV-1, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240, 2404, 404 (Top Transmission Shaft Front Seal)], [B-250, B-275, B-276, B-414, 2300, 2300A, 2424, 2444, 3414, 3444, 354, 364, 384, 424, 434, 444 (Bull Pinion Shaft Bearing Retainer Seal)], [Cub, Cub Lo-Boy, 154, 184, 185 (Final Drive Upper Pinion Shaft Seal)], [M, MD, MDV, MV (Transmission Counter Shaft Front Seal)], MTA (Front Wheel Seal; with single front 900 x 10 wheel), [O4, OS4 (PTO Output Shaft Seal; serial number 2159 to 9300)], [Super M, Super MD, Super MDV, Super MV (Transmission Counter Shaft Front Seal; up to serial number F52627 and up to seril number L51241)], W4 (PTO Output Shaft Seal; serial number 786 to 9300). Replaces: 21969D, 264694R91, 287440R91, 3043788R91, 3043788R92, 358765R91, 358784R91, 358808R91, 358823R91, 381907R91, 42177D, 43278D, 50839D, 530969R91, 703907R91, 703908R92, A29424. (Item #: 178204, Ref: 381907R91) $6.00
Rear Outer Flanged Axle Seal - This Rear Outer Flanged Axle Seal measures 2.125 inches inside diameter, 3.001 inches outside diameter and 0.434 inches wide. Fits A, AV, B, BN, Super A, Super A1, Super AV, Super AV1. Replaces original part numbers 358767R91, 358810R91, 43283D, 71697C1 (Item #: 167998, Ref: 15287A) $9.30
Rear Stub Axle Felt Washer - This Rear Stub Axle Felt Washer measures 2.920 inches outside diameter, 2.000 inch inside diameter and is 0.375 inches thick. A, AV, B, BN, Super A, Super A1, Super AV, Super AV1. Two used per tractor. Sold individually. Replaces: 15017D, 43242D. (Item #: 178083, Ref: 43242D) $10.60
Seal, Differential Ball Bearing - For tractor models A, A1, AI, AV, B, BN, Super A, Super A1, Super AV, Super AV1, 100, 130, 140. This seal measures 2.378 inches outside diameter, 1.531 inches inside diameter and 0.500 inches wide. wide. 2 used per tractor, sold individually. Replaces: 358773R91, 358813R91, 381742R91, 383340R91, 385865R91, 45175D, 46282D, 71597C1, 71597C91 (Item #: 172757, Ref: 71597C1) $26.20
Transmission Gasket Kit - This three piece Transmission Gasket Kit includes transmission shift cover gasket, transmission spline shaft bearing retainer gasket and counter shaft bearing cage gasket. It fits: A, AV, B, BN, Super A, Super A-1, Super AV, Super AV-1, 100, 130, 140. Replaces original part numbers 1342393C1, 46503D, 47279DA, 47283D, 47283DB (Item #: 178158, Ref: 1342393C1) $26.50

Electrical System
Alternator Bracket Kit - This alternator bracket has a 2 inch gap for the alternator part number 8NE10305SE and will fit the following tractor models A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 200, 230, will also work for Power units U2, U2A. (Item #: 127584, Ref: IHALTBKIT) $64.00
Distributor - Original IHC design comes with a 32 tooth drive gear. For tractor models A, AV, B, BN, C, Cub, Cub Lo-Boy, Cub 154 Lo-Boy, Cub 184 Lo-Boy, Cub 185 Lo-Boy, H, HV, I4, I6, I9, ID9, ID6, M, MD, MDV, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD-TA, Super MDV, Super MTA, Super MV, Super W4, Super W6. R6332 (Item #: 124839, Ref: 107304C91) $115.00
Distributor Dust Cover - Used with horizontal IHC distributor 353898R11 or J4 magneto on Models: A, AV, Super A, Super AV1, B, BN, C, Super C, Cub, Cub Lo-Boy, H, HV, Super H, Super HV, M, MV, MD, MDV, Super M, Super MD, Super MTA, W4, W6, W9, WR9, WR9S, WDR9, O4, O6, OS6, ODS6, I4, I6, ID6, I9, ID9, T6, TD6, TD9, 100, 130, 140, 154, 184, 185, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404. Replaces 384831R91. (Item #: 107074, Ref: 353900R11) $16.10
Distributor Shaft Bushing and Shim Kit - International Distributor Shaft Bushing and Shim Kit. Fits tractor models A, A1, AV, AV1, B, BN, C, Cub, Cub Lo-Boy, H, HV, M, MTA, MTAV, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A-1, Super AV, Super AV-1, Super C, Super H, Super HV, Super M, Super MTA, Super MV, Super W4, Super W6, 100, 130, 140, 154, 184, 185, 200, 230, 240, 2404, 2424, 2444, 300, 330, 340, 3444, 350, 3514, 400, 404, 424, 444, 450, 504, 600, 650. Replaces: 252739R1, 352298R1, 353899R1, 353921R1, 373577R91, 86637641. This is a 5-piece kit. The length is 2.006 inches. (Item #: 178766, Ref: IHS3166) $44.00
Magneto Rotor H4 Magneto - This Rotor is used on tractors with H4 magneto. Replaces 47425DX, 47425DY, 47428DA (Item #: 111106, Ref: 47425DY) $11.80
Rotor - Used with Delco distributors 1111411 with a clip held cap. For tractor models: A, I4, AV, Super A, Super AV, Super AV1, B, BN, C, Super C, H, HV, Super H, Super HV, M, Super M, MTA, Super MTA, MV, Super MV, O4, O6, OS4, OS6, T6, W4, W6, 354 (distributors with a tach drive). Replaces 3069778R1. (Item #: 110177, Ref: 1750498M1) $3.80
Spark Plug Wire Set, Custom - IH or Delco Distributors and Magnetos. For the following models with 90 degree angle boots: A, I4, AV, Super A, Super A1, Super AV, SuperAV1, B, BN, C, Super C, Cub, Cub Lo-Boy, 154, 184, 185, H, HV, Super H, Super HV, M, MD, Super M, Super MD, Super MDV, MDV, Super MDVTA, MTA, Super MTA, MV, Super MV, Super MVTA, O4, O6, ODS6, OS4, OS6, T340, T5, T6, TD6, SuperW4, W4, Super W6, Super W6TA, W6, W6TA, Super WD6, WD6, 100, 130, 140, 200, 230, 240, 300, 330, 340, 350, 400, W400, 404, 424, 444, 450, W450, 504. Replaces the following OEMS: 352947R91, 352951R91, 352954R91, 352956R91, 356687R92, 356689R92, 356691R91, 356694R92, 356695R92, 356697R93, 362439R91, 362789R91, 407487R1, 45327DA, 46277DA, 50075D, 52794D, 65352D, 65357D, 65358D, and 65359D. (Item #: 120100, Ref: S.67475) $17.50
Starter Nose Cone - This cast nose cone is used with starters that have saddle mount solenoids. Solenoid mount is not cast into this part. Bushing Included. Multi drilled and tapped for multiple applications. Used on Delco: 1107169, 1107358, 1107402, 1107407, 1107413, 1107414, 1107424, 1107434, 1107437, 1107439, 1107440, 1107443, 1107456, 1107458, 1107459, 1107542, 1107663, 1107682, 1107806, 1107813, 1107831, 1107958, 1107967, 1107976, 1108006, 1108009, 1108012, 1108038, 1108041, 1108060, 1108090, 1108621, 1108092, 1108103, 1108130, 1108142, 1108159, 1108165, 1109380, 1813397. Replaces Delco part numbers: 1813396, 1872960, 1874785, 1879052, 1914976, 1924299, 1924468, 1930639, 1935587, 1938304, 1959334, 1959773, 1963665 (Item #: 189672) $62.00

Engine Bearings
Main Bearings 0.030 - Main bearing set in 0.030. For C113 and C123 4-cylinder gas engines. (1 Kit used per engine). For tractor models A, AV, B, BN, Super A, Super AV, Super A-1, Super AV-1, C, Super C, 100, 130, 140, 200, 230, 240. Journal measures 2.095. YTO MBK113-030. Replaces 372116R91 and 7372116 (Item #: 106564) $75.01
Main Bearings .010 - Main bearing set in 0.010. For C113 and C123 4-cylinder gas engines. (1 Kit used per engine). For tractor models A, AV, B, BN, Super A, Super AV, Super A-1, Super AV-1, C, Super C, 100, 130, 140, 200, 230, 240. Journal measures 2.115. YTO MBK113-010. Replaces 376639R91 and 7376639. (Item #: 106562) $58.00
Main Bearings .020 - Main bearing set in 0.020. For C113 and C123 4-cylinder gas engines. (1 Kit used per engine). For tractor models A, AV, B, BN, Super A, Super AV, Super A-1, Super AV-1, C, Super C, F12, F14, 100, 130, 140, 200, 230, 240. Journal measures 2.105. YTO MBK113-020. Replaces 376642R91 and 7376642. (Item #: 106563) $85.00

Engine Gaskets
Head Gasket Kit - Upper gasket set with head gasket. For C123 CID gas 4 cylinder engine on tractors: Super A-1 and AV-1 serial number 310300 and up, Super C~ 100 and 200. For 400, 450, M, MD, MDV, MV, Super M, Super MD, Super MTA, Super W6, Super WD6, W400, W450, W6TA. (Item #: 106677, Ref: 357476R95) $72.00
Oil Seal - Fits: [A, AV, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, 230, 240 (use as a flat belt pulley shaft seal)], [H, HV, Super H, Super HV (use as a transmission counter shaft front seal)], [O4, W4 (Used as a brake shaft oil seal)]; The seal measures 1.375 inches inside diameter, 2.110 inches outside diameter, 0.315 inches wide. Replaces: 356502R91, 356503R91, 358781R91, 358820R91, 367810R91, 369146R91, 43308D, 43660D, 48308D, 48954D, 71700C1, 71701C1. (Item #: 152182, Ref: 71701C1) $10.50
Overhaul Gasket Set - For Super A1 and AV1 (serial number 310300 and up), Super C, 100, 130, 140, 230, 240, 330, 340 using C123 or C135 gas engines. Includes all gaskets including crankshaft seals. (Item #: 106716, Ref: GK7640S) $94.00
Seal, Crankshaft, Front with wear sleeve - Front Crankshaft Seal. For 100, 130, 140, 200, 230, 240, 330, 340, Super A-1, Super AV-1, Super C, Cub serial number <261717, Cub Lo-Boy serial number <261717. (Item #: 178053, Ref: 378193R91) $37.10
Valve Cover Gasket - This Valve Cover Gasket is used on Gas Engines; C113, C123, C135, C146, C153. It replaces OEM/Original part numbers 43378DB, 43378DD, 43378DE. (Item #: 128613, Ref: 43378DE) $10.60

Engine Rebuild Kits
Basic Engine Overhaul Kit, Less Bearings - Basic Engine Kit, less bearings for tractor models: Super A1 and Super AV1 serial number 310300 and up, Super C; 100 and 200 (C123 CID 4-cylinder gas). For tractors with stepped head pistons. Overbore from 3 1/8 inch to 3 1/4 inch. Kit contains sleeves and sleeve seals, pistons and piston rings, pins and retainers, complete gasket set with crankshaft seals. ENGINE BEARINGS ARE NOT INCLUDED. (Item #: 130578, Ref: BEKH1159-LCB) $456.00

Engine Parts
Camshaft Timing Gear - 66 teeth. For tractor models (100, 130, 140, 200, 230, 240, Super C all with 123 CID engine), (330, 340, 404 all with 135 CID engine), (424 with 146 CID engine), (444, 504 with 153 CID), (A, AV, B, BN, C, Super A, Super A1, Super AV, Super AV1 with 113 CID engine). Replaces 375712R1, 6779DB. (Item #: 111038, Ref: 375712R1) $86.00
Governor Spring - This Governor Spring is used internally in the following tractors: A, AV, B, BN, Super A, Super A1, Super AV, Super AV1, 100, 130, 2404 (With C-113, C-123 or C-135 engines), 404. It replaces: 46944DA (Item #: 179295, Ref: 46944DA) $13.90
Valve, Exhaust - For Models: A, AV, Super A and Super AV serial number 255418 to serial number 310299, and C. (flat head compression piston) (cylinder sleeve 3-5/16 inch outside diameter at seal) (1.160 inch head diameter, 4.940 inch length, 45 degree). Sold single. (Item #: 128524, Ref: 57798D) $13.50
Valve, Intake - For tractor models: A, AV, Super A and Super AV serial number 255418 to serial number 310299, and C. (flat head compression piston) (cylinder sleeve 3-5/16 inch outside diameter at seal) (1.340 inch head diameter, 4.940 inch length, 45 degree). Sold single. (Item #: 128523, Ref: 57797D) $11.00
Valve Spring - Used on valves with length of 5-5/16 inch. For tractor models 100, 130, 140, 200, 22, 230, 240, 62, 76, 81, A, AV, A1, AV1, B, BN, C, H, HV, O4, OS4, Super A, Super AV, Super AV1, Super C, (U2, U2A serial number less than 22113), W4. 8 Used Per Tractor. Sold individually. (Item #: 128518, Ref: 24544DA) $3.30

Engine Pistons and Sleeves
Pin Bushing - This Piston Wrist Pin Bushing Is used on 113 and 123 Gas and LP Engines. 0.909 inch I.D. 0.993 Inch O.D. 1.216 inch overall length. Pin Bushings require honing after installation. Replaces: 24415D, 64508D (Item #: 108092, Ref: 64508D) $10.00
No Picture Sleeve and Piston Kit, Stepped Head Pistons - Stepped Head Piston Set (will replace flat head piston). Piston Pin Diameter .919 inch. Overbore 3 1/4 inch. 3.436 (3 7/16) inch lower sleeve diameter. For Super A1 and AV1 serial number 310300 and up, Super C; 100 and 200 (C123 CID 4-cylinder gas). Overbore from 3 1/8 inch to 3 1/4 inch. Contains (4) sleeves, (4) pistons, all rings, pins and retainers. (Item #: 184516, Ref: PK159) $489.00
No Picture Sleeve Assembly - C123 CID 4 cylinder gas engines with stepped head pistons. 3-7/16 inch outside diameter at seal area. For tractor models 100, 200, Super AV serial number 310300 and up, Super AV1 serial number 310300 and up, Super C. (Item #: 173469, Ref: SK275) $136.00
No Picture Sleeve Seals - For 1 cylinder. For tractor models 200, Super AV, Super AV1, Super C, 100 all with C123 engine. For tractor models 330, 340 both with C135 engine. (Item #: 128639, Ref: SRK701) $5.60

Engine Rings
Piston Ring Set - Ring set for 4 pistons, for C123 CID gas 4 cylinder engine. Overbore 3-1/8 inch to 3-1/4 inch. Contains (for each Piston): 3 compression rings at 3/32 and oil ring at 3/16 per cylinder. For tractors: Super A-1 AV-1 serial number 310300 and up. Super C~ 100 and for H, HV, O4, OS4, W4. Replaces 31R500, 2C4215, RP191451 (Item #: 185209, Ref: PRS159) $83.00

Exhaust System
Muffler - Vertical muffler for gas tractors. Inlet inside diameter 1-15/16 inch, outlet outside diameter 2 inch, length 29 inch, diameter 4-1/4 inch round body. Fits engines C113, C123, C135. For tractor models: A, AV, Super A, Super AV, B, BN, C, Super A-1, Super AV-1, 330, Super C, 100, 13 For 100, 130, 140, 200, 230, 240, 2404, 330, 340, 404, A, AV, B, BN, C, Super A-1, Super AV, Super AV-1, Super C, Super A. (Item #: 133340, Ref: 360720R91) $33.00
Muffler - Vertical muffler for gas tractors. Fits short clearance muffler for tobacco or grove application, engines: C113, C123, C135. Inlet inside diameter 1-15/16 inch, outlet inside diameter 2 inches, length 18 inches, diameter 4-1/4 inches, round body. For tractor models A, AV, Super A and AV, B and BN, C, Super For 100, 130, 140, 200, 230, 240, 2404, 330, 340, 404, A, AV, B, BN, C, Super A-1, Super AV, Super AV-1, Super C, Super A. (Item #: 178978, Ref: 360720TOB) $83.00

Fuel System / Air Intake
Carburetor - Zenith carburetor outperforms the original carbs used on: 130, 140, 230, 56T, 56W, 57T, 57W, C, Super A-1, Super AV-1, Super C. Replaces: 373957R91, 373959R91, 373961R91, 372098R93, 366462R94, 366306R91, 366306R92, 366306R93, 373962R91, 373978R91, 354892R92, 354892R91, 372983R91, 354892R93, 52499DA, 385507R91, 385608R91, 48616D, 362385R91, 362384R91, 69402D, 69401D, 69404D, 377600R91, 375560R91, 52499DC, 52499DD, 52499DE, 352047R91, 372985R92, 355485R92, 356901R91, 356902R92, 355485R91, 3454892R92, 352377R92, 354184R93, 354185R92, 52499DB. Zenith 8928, 9167, 9749, 9752, 10386, 10522, 11115, 11188, 11340, 11704, 12115, 12122, 12123, 12225, 12285, 12475, 12522, 12613, 12613A, 14007, Marvel Schebler TSX156, TSX157, TSX171, TSX198, TSX319, TSX333, TSX348, TSX730, TSX744, TSX926 Mounting holes are 2-3/8 inches center to center. Made in USA, 1 year warranty. (Item #: 182605, Ref: 12911) $440.00
Carburetor Choke Lever - This choke lever is used on carburetors with a splined choke shaft. Fits: Zenith carburetors 9748, 9749, 9750, 9752, 10112, 10386A, 10386B, 10386C, 10441, 10441A, 10498, 10514, 10514A, 10522, 10522A, 10652. Marvel Schebler carburetors TSX156, TSX157, TSX171, TSX198, TSX319, TSX333, TSX347, TSX348. International / Farmall carburetors 352376R92, 354184R93, 355485R91, 373957R91, 52499DB, 69401D Replaces original part number 8639D. (Item #: 126958, Ref: 8639D) $24.50
Fuel Sediment Bowl Bail Assembly - This bail fits 1.280 inch tall glass bowls. It is 2.700 inches in length. Replaces OEM numbers: 0W446, 1001515M91, 15P15, 1JS-5305, 223247, 2N9166, 49947DX, 70223247, A11212 (Item #: 113631, Ref: 2N9166) $5.95
Sediment Bowl Gasket and Screen - This is a 2 Inch Outside Diameter Gasket and Screen. The Screen has a 3/8 Inch center hole. (Item #: 105364, Ref: 49923D) $3.50

Hydraulic System
Hydraulic Pump Gear - This New Hydraulic Pump Gear has 16 teeth. It Fits: C, Super A, Super A-1, Super AV-1, Super C, T340 (gas with 9 GPM side engine mounted pump), [ T4, T5 (gas with 9 GPM side engine mounted pump) ], 100, 130, 140, 200, 230, 240, [ 2424, 2444, 340, 424, 444 (GAS) ], 330, 404, Crawler: 500 (GAS with 9 GPM side engine mounted pump). Replaces: 350709R1. (Item #: 121576, Ref: 350709R1) $104.00
Hydraulic Pump Kit - This is a Thompson Hydraulic Pump Gasket, O-Ring and Seal Kit used on Thompson 360945R91 and 360945R92 hydraulic pumps. Used on 100, 130, 140, 200, 230, C, Super A, Super A1, Super AV, Super AV1, Super C. Contains Gasket 350708R2 (350708R1), Gasket 350706R3, Oil seal 385038R91 (353183R91), Main body O-ring 510185 (293726R1), O-ring 352024R2, 2 O-rings 75285739 (350667R1), Woodruff key 126-109 (106749), Jam nut 124925 (114494). Replaces 360957R91 (Item #: 184756, Ref: 360957R91) $57.00
Hydraulic Pump Kit - This is a Pesco Hydraulic Pump Gasket, O-Ring and Seal Kit used on Pesco Pumps: 360689R91, 350707R96, 355007R91, 355007R92, 355007R94, 355370R93. Tractor Models: 100, 130, 140, 200, 230, C, Super A, Super A1, Super AV, Super AV1, Super C. This is an 18 piece kit and includes: Gasket 350706R3, Gasket 350708R2 (350708R1), Quad ring G46055 (353186R1), 2 O-rings 86553262 (253070R1), 2 O-rings 75285739 (350667R1), 2 O-rings 353184R1, 2 O-rings 355202R1, 2 Washers 355048R1, O-ring 353836R1, Woodruff key 124543 (106749, 126109), Jam nut 124925 (114494), Pin seal 353185R1, Oil seal 385038R91 (353183R91) used on early pumps. Replaces 354405R92, 355207R91, 360691R91, 355405R93, 355405R91 (Item #: 178947, Ref: 354405R92) $73.00
Hydraulic Pump Mounting Gasket - Used on many Farmall / International models, this gasket replaces OEM part numbers: 251068R1, 355362R91, 350708R1, 360691R91, 360957R91, 761107R93, 762318R91, 762200R92, 762309R91, 762428R91, 762197R91, 764940R91 (Item #: 167973, Ref: 350708R2) $2.60
Touch Control Piston Sleeve Boot - This touch control piston sleeve boot fits the following tractor models: C, Cub, Cub Lo-Boy, Super A, Super A1, Super AV, Super AV1, Super C, 100, 130, 140, and 200. It has an overall length of 2.425 inches, an overall outside diameter of 1.235 inches, a top hole diameter of 0.530 inches, and a bottom hole diameter of 0.875 inches. Replaces 351754R3, 364833R2. (Item #: 182534, Ref: 351754R3) $10.30
Touch Control Valve Boot - This touch control valve boot fits the following tractor models: Cub, Cub Lo-Boy, Super A, Super A1, Super AV, Super AV1, Super C, 100, 130, 140, and 200. It has an overall length of 2.450 inches, an overall outside diameter of 1.500 inches, a top hole diameter of 1.755 inches, and a bottom hole diameter of 0.725 inches. Replaces Leather Boot: 351753R3, 364832R1, 364832R2. (Item #: 178168, Ref: 351753R3) $11.30

Oil System
Oil Pan Drain Plug - White Zinc Finish, 7/8 inch - 18 UNF. Fits multiple models. Order EBU6734A if washer is needed. Replaces: 688067C1, 359875R1. (Item #: 126591, Ref: C5NE6730B) $8.10
Oil Pan Drain Plug Washer - This washer is used with C5NE6730B 7/8 inch Oil Drain Plug. (Item #: 140612, Ref: EBU6734A) $1.70

PTO / Driveline
PTO and Belt Pulley Gasket Kit - This PTO and Belt Pulley Gasket Kit is four pieces containing one PTO to rear end housing gasket, one belt pulley cover gasket, one belt pulley shaft bearing cage gasket and one PTO drive bearing cage gasket. Used on: A, AV, B, BN, C, Super A, Super A1, Super AV, Super AV1, Super C, 100, 130, 140, 200, 230 and 240. Replaces: 1342404C1, 1342405C1, 46061DA, 47283D, 47283DA, 47283DB, 60581D, 60589D, 60589DA, 63779D (Item #: 178081, Ref: IHS2358) $28.40

Seats
Leaf Spring, Seat, LH - For tractor models A, Super A, A1, Super A1, AV, Super AV, AV1, Super AV1, B, 100, 130, 140, 444, 2444. (Item #: 109588, Ref: 50586DB) $35.00
Leaf Spring, Seat, RH - For tractor models A, Super A, A1, Super A1, AV, Super AV, AV1, Super AV1, B, 100, 130, 140, 444, 2444. (Item #: 112485, Ref: 50587DB) $35.00
Seat Support Bracket - Left - This Seat Support Bracket fits A, AV, B, BN, Super A, Super A-1, Super AV, Super AV-1, 100, 130, 140. Powder Coated. Replaces: 350007R2, 350007R3, 51181D (Item #: 126671, Ref: 51181D) $99.30
Seat Support Bracket - Right - This Seat Support Bracket fits A, AV, B, BN, Super A, Super A-1, Super AV, Super AV-1, 100, 130, 140. Powder Coated. Replaces: 51182D (Item #: 126672, Ref: 51182D) $99.30

Sheet Metal / Body Parts
Battery Lid T Bolt - This T bolt is used to attach the battery lid to the battery box for the following tractor models:A, A1, AV, AV-1, B, BN, C, Super A, Super A-1, Super AV, Super AV-1, Super C, 100, 130, 140, 200, and 230. Replaces: 50939DA and 50939DX. (Item #: 178094, Ref: 50939DA) $5.40

Steering
Steering Sector Bushing, Bearing and Seal Kit - This 11-Piece Steering Sector Bushing, Bearing and Seal Kit Includes: Steering worm shaft bushing, steering wheel shaft bushing, steering worm wheel shaft bearing, steering worm bearing, steering gear housing gasket, steering worm oil seal, and steering worm wheel shaft oil seal. Bushings must be honed (reamed) to size when installed. Fits: A, AV, Super A, Super A1, Super AV, Super AV1, 100, 130, 140; Replaces: 1981225C1, 261733, 2099680, 358775R91, 358782R91, 358812R91, 358815R91, 382229R91, 382229R91, 382230R91, 41096DBR, 47675D, 47676DR, 47703D, 48956D, 85652H, R39667, ST287, ST288 (Item #: 182546, Ref: IHS1800) $87.00
Steering Wheel Nut - This steering wheel nut fits the following tractor models: Cub Cadet 100, Cub Cadet 102, Cub Cadet 122, Cub Cadet 70, A, AV, AV1, B, BN, C, H, HV, I4, I6, I9, ID6, ID9, M, MD, MDV, MTA, MV, O4, O6, ODS6, OS4, OS6, Super A, Super A1, Super AV, Super AV1, Super C, Super H, Super HV, Super M, Super MD, Super MDV, Super MDVTA, Super MTA, Super MV, Super MVTA, Super W4, Super W6, Super W6TA, Super W9, Super WD6, Super WD6TA, Super WD9, Super WDR9, W4, W6, W9, WD6, WD9, WDR9, WR9, WR9S, 100, 130, 200, 230, 600, 650, Cub Lo-Boy, 300, 400, 450, and Cub. It measures 0.75 inches wide, 0.444 inches tall, and has a 16 NF thread size. Replaces part numbers: 114499, 122403, and 219753. (Item #: 157780, Ref: 353435X1) $1.00
Steering Wheel Shaft Worm Oil Seal - This steering wheel shaft worm oil seal measures 1.000 inch inside diameter, 1.624 inch outside diameter and has a .250 inch width. Used on A, AV, Super A, Super A-1, Super AV, Super AV-1, 100, 130, 140 all with Long Steering Wheel Shaft. Replaces: 358229R91, 358782R91, 358821R91, 383332R91, 48956D. (Item #: 126728, Ref: 48956D) $15.60
Tie Rod End, Inner, RH Thread - 3-1/8 inch to center of post, .687 inch shaft diameter, 18 thread, used on tie rod assemblies with notched outer end and threaded inner end, for swept back adjustable axles 44 inches to 72 inches. For tractor models 100, 130, 140, 330, 340, 404, 424, 444, 454, 464, 484, 504, C, Cub Lo-Boy, Super A-1, Super AV, Super AV-1, Super C, Super A. (Item #: 100859, Ref: 356540R91) $17.00
Universal Parts and Accessories Category: Accessories / Supplies

Accessories / Supplies
Auxiliary Heater, Universal - This universal auxiliary heater is used for tractor cabs, combines, backhoes, dozers, forklifts, etc. using 5/8 inch heater hose connections. Hot water forced air heat. Dimensions: 6-1/2 inches x 9-1/2 inches x 9 inches, steel powder coat housing with aluminum core. 3-speed high volume squirrel cage fan, 12-volt, 20, 000 BTU includes switch, brackets, instructions. (Item #: 182644, Ref: MIS3127) $385.00
Magnetic Block Heater - Universal. Magnetic utility heater. 120 volt AC, 200 Watts. Built-in thermostat maintains optimum temperature - will not exceed 250 degree F (121 degree C). Quick-grip handle protects hands from heat. 4-3/8 inches (11cm) length, 2-1/2 inches (6.3cm) width, 3 inches (7.5cm) height (including handle). (Item #: 178758, Ref: MBH1153) $97.00

Decals and Emblems
Decal, Fear This IH - Black and red, 12-1/2 x 3-3/4. For all Models. (Item #: 183484, Ref: S.67826) $15.80
Decal, IH Block - "IH" logo, 11 inches. (Item #: 183564, Ref: R4682) $17.40
Decal, IH Block - "IH", 3 inch x 3 1/4 inch Block. (Item #: 101094, Ref: R4681) $6.40
Decal, IH Block - "IH" logo, 1 3/4 inch. (Item #: 183266, Ref: R4680) $5.00
Decal, IH Block - "IH", 1 1/4 inch Logo . (Item #: 183058, Ref: R4679) $3.90
Decal, IH Block - "IH" logo, 7 inches printed on vinyl. (Item #: 183292, Ref: R5171) $25.80
Decal, IH Block - "IH" logo, 8 inches printed on vinyl. (Item #: 183123, Ref: R5172) $30.50
Decal, IH Block - "IH" logo, 10 inches. (Item #: 183276, Ref: R5173) $36.60
Decal, IH Block - "IH" logo no background, 1 inch printed on vinyl. (Item #: 183334, Ref: R5174) $2.60
Decal, IH Block - "IH" logo no background, 1-5/8 inches printed on vinyl. (Item #: 183338, Ref: R5175) $3.90
Decal, IH Block - "IH" logo no background, 2 inches x 2-1/2 inch printed on vinyl. (Item #: 183347, Ref: R5176) $5.00
Decal, IH Block - "IH" logo no background, 3 inch x 3-1/2 inch printed on vinyl. (Item #: 183352, Ref: R5177) $14.20
Decal, IH Block - "IH" logo no background, 4-1/2 inch x 4-3/4 inch printed on vinyl. (Item #: 183255, Ref: R5178) $7.50
Decal, IH Block - "IH" logo no background, 5-1/2" x 6" printed on vinyl. (Item #: 183265, Ref: R5179) $16.60
Decal, IH Block - "IH" logo no background, 6-1/2 inch x 7 inch. (Item #: 183547, Ref: R5180) $12.40
Decal, IH Block - "IH" logo no background, 7-1/2 inch x 8 inch. (Item #: 183556, Ref: R5181) $14.80
Decal, IH Block - "IH" logo on silver background, 2 inch x 2-1/4 inch. (Item #: 183560, Ref: R5182) $14.20
Decal, IH Block - "IH" logo no background, 10 inch x 11 inch. (Item #: 183543, Ref: R5183) $25.50
International Decal - 8-1/2 inch long, white with black outline. (Item #: 183068, Ref: R0679) $9.40
International Decal - 23 inches long, black block letters. (Item #: 183477, Ref: R0680) $12.40
International Decal - 23 inches long, white with black outline. (Item #: 183478, Ref: R0681) $16.60
International Decal - 26 inches long, black block letters. (Item #: 183481, Ref: R0682) $14.80
International Decal - 26 inches long, white with black outline. (Item #: 101032, Ref: R0683) $14.00
International Decal - 29 inches long, black block letters. (Item #: 101030, Ref: R0684) $10.50
International Decal - 29 inches long, white with black outline. (Item #: 101033, Ref: R0685) $17.50

Electrical System
NOTE Alternator - Don't see the Alternator you need for your tractor? We have many alternators not listed on this website (for tractors 1953 and newer). Just call us at 800-853-2651.	NOTE
No Picture Alternator, 12 Volt - Universal 63 Amp Delco Alternator. Single wire with built in regulator. Will fit most tractors pre 1980. (Item #: 111377, Ref: 8NE10305SE) $96.00
Alternator Conversion Plug - Used to turn Delco SI Style 2-Wire plug alternators into self-exciting style. (Item #: 178026, Ref: ADR9209) $14.40
Alternator Top Adjusting Bracket, Universal - Universal Top Adjusting Bracket for Alternator or Generator is 7/8 inches wide, 1-1/2 inch offset, 8-1/4 inch from farthest end of slot to center of mounting hole, 3-3/4 inch slot length, 3/8 inch mounting hole. (Item #: 173326, Ref: 8NL10302) $25.20
No Picture Battery Thermal Wrap - 60 Watt, 28 inches long wrap to keep your battery warm. (Item #: BTW28) $35.98
No Picture Battery Thermal Wrap - 160 Watt, 36 inches long wrap to keep your battery warm. (Item #: BTW72) $53.81
No Picture Coil - This universal automotive style coil is 28, 000 volts for a 12 volt system, 2.9 ohms. Measures 6 inches long and 2 1/2 inches diameter. (Item #: 182583, Ref: 28010) $49.20
Distributor Cap, WICO - For All Models with WICO distributor having clip type cap with 3 3/8 inside diameter seat. (Item #: 108299, Ref: X30042) $62.15
Magneto, Wico XH and XHD, Service and Parts Manual - Wico XH And XHD magneto service instructions and parts list. This is a reprint of the original manual that has exploded views of all parts on the tractor with numbered pictures giving great detail on assembly and disassembly. It also gives you a guide with numbers for ordering parts. (Item #: 182504, Ref: MAG6) $19.20
No Picture Spark Plug - Extended tip, 14mm thread, 3/8 inch reach. Replaces Champion J10Y, J11Y, J12Y, J13Y. NOTE: Verify spark plug type before ordering. (Item #: 179437, Ref: AL85) $5.60
Spark Plug - Standard tip, 14mm thread, .472" reach. Replaces Champion L9J, L10, L86, L86C, L88A, L90. NOTE: Verify spark plug type before ordering. (Item #: 182459, Ref: AL425) $4.80
NOTE Starter - Don't see the starter you need for your tractor? We probably have it! Just call us at 800-853-2651 with your make, model, engine cubic inches (CID) and number off your old starter and we will see if we can find it!	NOTE
Starter, Generator, Distributor Tag, 6 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182608, Ref: DELCO6) $16.80
Starter Solenoid - This is a 3 post, 12 volt Starter Solenoid. Can be used as a saddle mount or flat surface mount. May come in a metal or plastic casing. Replaces: 1114200, 1114207, 1114216, 1114225, 1114235, 1114545, 1114548, 1118820, 1996067, D928, DR1467, DR1485. May come in a silver metal casing versus black plastic. (Item #: 150223, Ref: DR1467) $19.20
Tag for Starter/Generator, 12 Volt, Blank - Comes with 2 rivets. 2.5" long, .800" wide, 2" center to center rivet hole, .150" dia. rivet holes. Customer must stamp numbers. (Item #: 182606, Ref: DELCO12) $16.80
Voltage Regulator, 12 Volt - 4-terminal flat mount. The Three Post side of this regulator may be parallel or slightly splayed. Fits most 12V tractors and combines prior to 1957. (Item #: 105581, Ref: 182548M92) $25.00

Engine Gaskets
Silicone Blue RTV - Permatex ultra blue, no leak RTV silicone gasket, oil resistant, use on valve covers, oil pans, timing covers, water pumps. Temperature range -75 degree F to +500 degree F, 3.35 ounce tube. (Item #: 178141, Ref: PRM77BR) $10.90

Exhaust System
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 118823, Ref: ZNL89020C) $81.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 2.5 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119038, Ref: ZNL89025C) $108.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 3.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114858, Ref: ZNL89051C) $135.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.00 inch inside diameter inlet with extended curve. This is a universal part. Verify measurements before ordering. (Item #: 173286, Ref: 146520CHR) $106.00
Chrome Exhaust Stack - Single wall, 53 inches long with a slotted, 3.50 inch inside diameter inlet. It has an extended curve on the outlet. This is a universal part. Verify measurements before ordering. (Item #: 173287, Ref: 146490CHR) $161.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 4.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 114945, Ref: ZNL89057C) $145.00
Chrome Exhaust Stack - Single Wall, 48 inches long with a slotted, 5.00 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 119080, Ref: ZNL89485C) $174.00
Chrome Exhaust Stack - Single Wall, 42 inches long with a slotted, 2.50 inch inside diameter inlet. This is a universal part. Verify Measurements before ordering. (Item #: 173281, Ref: L102236CHR) $88.00
Muffler Clamp, 1-1/4 - New Clamp for 1-1/4 inch outside diameter muffler inlet. (Item #: 182682, Ref: MC114) $2.10
Muffler Clamp, 1-3/4 - New Clamp for 1-3/4 inch outside diameter muffler inlet. (Item #: 108866, Ref: MC134) $4.80
Muffler Clamp, 1-3/8 - New Clamp for 1-3/8 inch outside diameter muffler inlet. (Item #: 182687, Ref: MC138) $2.90
Muffler Clamp, 2-1/4 - New Clamp for 2-1/4 inch outside diameter muffler inlet. (Item #: 108870, Ref: MC214) $5.30
Muffler Clamp, 2-3/4 - New Clamp for 2-3/4 inch outside diameter muffler inlet. (Item #: 108872, Ref: MC234) $8.71
Muffler Clamp, 3 - New Clamp for 3 inch outside diameter muffler inlet. (Item #: 108873, Ref: MC300) $7.40
Muffler Clamp, 3-1/2 - New Clamp for 3-1/2 inch outside diameter muffler inlet. (Item #: 108874, Ref: MC312) $8.00
Muffler Clamp, 4 - New Clamp for 4 inch outside diameter muffler inlet. (Item #: 108875, Ref: MC400) $8.30
Muffler Clamp, 5 - New Clamp for 5 inch outside diameter muffler inlet. (Item #: 118841, Ref: MC500) $12.70
Rain Cap - This rain cap is for a 1.750 inch pipe. (Item #: 108632, Ref: R1799) $11.00
Rain Cap - This rain cap is for a 2.0 inch pipe. (Item #: 108633, Ref: R1800) $8.80
Rain Cap - This rain cap is for a 2.50 inch pipe. (Item #: 108635, Ref: R1802) $12.50
Rain Cap - This rain cap is for a 2.750 inch pipe. (Item #: 108636, Ref: R1804) $11.08
Rain Cap - This rain cap is for a 4.0 inch pipe. (Item #: 108645, Ref: R1807) $12.90
Rain Cap - This rain cap is for a 4.50 inch pipe. (Item #: 108749, Ref: WC14) $13.40
Rain Cap - This rain cap is for a 5.0 inch pipe. (Item #: 108750, Ref: WC15) $17.40
Stainless Steel Clamp, 2.75 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 179749, Ref: ZNL90872A) $6.50
Stainless Steel Clamp, 4 Inch - This Stainless Steel Clamp is used with Chrome Stacks and in other applications. (Item #: 185428, Ref: ZNL90875A) $8.50

Fuel System / Air Intake
Air Cleaner Filler - Fits many air cleaners that use steel wool type filler. Custom manufactured mesh. 1 bag = 3-1/2 inch x 3-1/4 inch. (Item #: 151026, Ref: S.43231) $14.00
Fuel Tank Screen - This Fuel Tank Screen is used with most stem-type sediment bowls to further protect against debris in the gas line. It has a 0.216 inch Insert Pipe outside diameter - 2.53 inch Overall Length. (Item #: 114940, Ref: R7949) $9.92
Main Fuel Valve - This main fuel valve replaces the original fuel solenoid for International carburetors. The original fuel solenoids are very unreliable and can easily be replaced with this manual valve. This assembly contains: the valve, graphite packing, and packing nut. Used on Carburetors: 50981DC, 45108DB, 50983DC, 52814DA, 47387DC, 361525R92, 358065R92, 362173R92, 367259R92, 380956R91, 380956R92, 380956R93, 381983R91, 381984R95, 389511R92, 367258R92, 396966R91, 388296R91, 388424R96, 396197R96, 396198R92, 381419R91, 397224R93, 381420R91, 357231R91, 356948R92. Replaces 47404DA, 374327R1, 362526R1, 362525R1 (Item #: 117537, Ref: 47404DASSY) $30.10
Sediment Bowl Gasket, 2-1/8 inch - For bowls with 2-1/8 inch diameter, 2.150 inch outside diameter. Made in the USA. (Item #: 112364, Ref: C1778R) $3.30

Gauges
No Picture Amp Gauge - This amp gauge comes with the "IH" logo printed on the face. It has a black face, chrome bezel, and reads 60-0-60. (Item #: 178963, Ref: IHS1837) $30.00
No Picture Hourmeter - DC voltages from 12 volt thru 36 volt nominal. Heavy duty glass-reinforced polyester body. Internal shock shields and grommets protect movement from shock and vibration damage. Fits 2-1/4 inch opening, three (3) mounting screws with nuts and two (2) blade terminals included. (Item #: 178318, Ref: HM771) $63.00
Hourmeter, Analog - 2 inch, black. Can be used on any tractor with a 12 to 24 volt electrical system. (Item #: 178285, Ref: S.52672) $42.30
Oil Gauge - For IHC and Farmall tractors 1947 and and up. Oil Pressure Gauge with color band - Includes mounting bracket. Has IH logo on face. (Item #: 110849, Ref: 41934DB) $49.57
Oil Line Adapter - Oil Gauge fittings may be different even for the same models. Here is an Oil Line Adapter if you have a gauge line without removable fittings, this converts 1/8 inch pipe thread to 1/8 inch tube. Brass. (Item #: 179540, Ref: 919095) $16.00

Hitch / Drawbar
Conversion Tong - Two Point Conversion Tong straight left hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184153, Ref: FH1447) $364.00
Conversion Tong - Two Point Conversion Tong straight right hand Tong with combination Cat. I and Cat. II Ball. For converting IHC Two Point Fast Hitch to Three Point. About 28 inches overall length. (Item #: 184167, Ref: FH1448) $364.00
Conversion Tong - Two Point Conversion Tong bent type, and Cat. II Ball. Left Hand. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179611, Ref: FH14416) $439.00
Conversion Tong - Two Point Conversion Tong bent type, right hand Tong with combination Cat. I and Cat. II Ball. Right Hand. The Bent Type spaces out at 32 inches between the ends of the tongs. The Non-Bent Type spaces out at 26 inches between the ends of the tongs. For converting IHC Two Point Fast Hitch to Three Point. About 32 inches overall length. (Item #: 179008, Ref: FH14417) $439.00
Hair Pin Assortment - 15-piece assortment. Includes four (4) of HP-3 (wire diameter 3/16 inch, length 3.75 inch), four (4) of HP-4 (wire diameter 5/32 inch, length 2 15/16 inches), four (4) of HP-5 (wire diameter 1/8 inch, length 2 9/16 inches), and three (3) of HP-6 (wire diameter 3/32 inch, length 1 5/8 inches). (Item #: 182461, Ref: HPA15X) $12.17
Universal Drawbar Lock - For Cat. 1 drawbars up to 1 1/2 inch thick and 3 inches wide. Prevents drawbar from rotating. (Item #: 112156, Ref: DBL2) $37.00

Hydraulic System
Filter Element - 25 Micron replacement element for SF1-25. (Item #: 182541, Ref: 1A9023) $15.40
Filter Element - 10 Micron replacement element for SF1-10. (Item #: 120092, Ref: 1A9021) $13.60
Hydraulic Hose Assembly-NPT, 12 inch - Universal. 12 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118257, Ref: H42-2M-12) $11.00
Hydraulic Hose Assembly-NPT, 180 inch - Universal. 180 inch (15 Feet) overall length. 1/2 inch inside diameter. 2 Wire. Solid Male 1/2 inch NPT thread on both ends. (Item #: 179906, Ref: H42-2M-180) $55.50
Hydraulic Hose Assembly-NPT, 24 inch - Universal. 1/2 inch I.D. double wire braid (SAE-2R) with 1/2 inch NPT solid male fittings both ends. 24 inch overall length. Replaces OEM # - 407435R1. (Item #: 118256, Ref: H42-2M-24) $14.10
Hydraulic Hose Assembly-NPT, 30 inch - Universal. 30 inch overall length. 1/2 I.D. 2 Wire. Solid Male 1/2 NPT thread on both ends. (Item #: 118259, Ref: H42-2M-30) $16.10
Hydraulic Hose Assembly-NPT, 48 inch - Universal. I.H.C.: 1/2" I.D. double wire braid (SAE-2R) with 1/2" NPT solid male fittings both ends. 48" overall length. Replaces OEM # - 407437R1. Hydraulics: 48 inch overall length (Item #: 118261, Ref: H42-2M-48) $16.50
Universal Pressure Gauge, Hydraulic - 1000 Lb. Gauge. Glycerin Filled. Stainless Steel Case 2-1 2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1 4 NPT male brass fitting. (Item #: 172285, Ref: GG1000) $13.50
Universal Pressure Gauge, Hydraulic - 60lb Gauge. Glycerin Filled. Stainless Steel Case 2-1/2 diameter. Nickel silver movement accurate to within 2%. Dual range KPA-PSI. Plexiglass crystal. 1/4 NPT male brass fitting. (Item #: 172338, Ref: GG60) $13.91

Implements
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Axle Bolt - Axle bolt, 1 each (Ref 3). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36 (Item #: 170217, Ref: BH1317) $14.90
Bearing cone (L44643) - For Caster Assembly, requires 2.Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 114630, Ref: 22) $5.90
Bearing Cup - This part fits Caster Assembly (Part Number BH215, Ref #6). Sold individually, two used per caster assembly. Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. Also replaces 132709, 15191, 32190M1, L44610. (Item #: 169771, Ref: 170BH) $7.86
Caster Assembly - Tail wheel and hub assembly with grease fitting and fork assembly. Shaft on Yoke is 1-1/2 inches diameter, 8 inches overall length, 7-1/4 inch to pin hole. New style tail assembly, used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405. Wheel must be attached to fork. For Bush Hog cutters with SPB40 spacer (included), assembly will also replace all models with Timken bearings. (Item #: 173612, Ref: 12269) $183.00
Caster Assembly, Old Style - Tail Wheel and Hub Assembly with grease fitting. 4 x 8 inch rim, 15 inch outside diameter of wheel. Includes wheel, hub, axle bearing and bolt assembly. OLD style tail assembly used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Wheel must be attached to fork. For Bush Hog cutters. With SPB40 spacer, assembly will also replace all models with Timken Bearings (Ref #1-#11). (Item #: 161111, Ref: BH215) $132.00
Hub Assembly - Hub with bushings (3/4 inch), wheel bolts (4), and grease fitting. Center tube length 5 inches. For rotary cutters: RB60 with new style 1-1/4 inch diameter caster, SM60R, SM160R; Squealer models: 1207, SQ36, SQ48, SQ60, SQ72, SQ148, SQ480. Replaces 60978, 60990, 63812. Can use 500BH tail wheel. (Item #: 180514, Ref: 63813BH) $38.10
Hub with Bearing Cups - 4-bolt, 5 inch bolt circle and 3-5/8 inch wheel pivot hub with bearing cups (1 inch axle) (Ref #5). This part fits caster assembly (part number BH215). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36. (Item #: 182627, Ref: BH1311) $49.30
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 31.5 Inches - Fully Hardened. Also replaces Kverneland 221151. (Item #: 182589, Ref: 221129) $51.00
No Picture Round Bale Tine 38.5 Inches - Fully Hardened. Also replaces Kverneland 241107, 241161. (Item #: 182592, Ref: 241100) $91.48
No Picture Round Bale Tine 43 Inches - Fully Hardened. (Item #: 182594, Ref: 241166) $111.54
No Picture Round Bale Tine 49 Inches - Fully Hardened. (Item #: 152690, Ref: 241162) $78.00
No Picture Round Bale Tine 55 Inches - Fully Hardened. (Item #: 182593, Ref: 241163) $131.61
Seal, Caster - Seal, 2 required (Ref #2). Used on many Bush Hog rotary cutters. Used on models 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405, 1406, 2510, 2512, 3108, 2309, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. (Item #: 180300, Ref: 30BH) $4.30
Tail Wheel Assembly - 4 inch x 8 inch tail wheel assembly with laminated tire. 3-5/8 inch pilot, 4 bolt holes, 5 inch bolt circle, 3-3/4 inches wide, 15 inch outside diameter. Used on the following Bush Hog cutters: 12, 104, 105, 109, 126, 205, 255, 275, 285, 305, 306, 307, 405, 405HR, 406, 406HR, 502, 600, 1050, 1051, 1109, 1126, 1207, 1209, 1226, 1306, 1307, 1405 and 1406, 2510, 2512, 3108, 3209, BD90, FH162, S268, SM60, SQ36, SQ480, SQ600. Replaces Sidewinder 15205, Servis Rhino 373024H, Terrain King 373024H, Modern 401-0048, BMB 5337, Hardee C40-RC, King Kutter KK4X8. (Item #: 111222, Ref: 500BH) $56.00
No Picture Talc Powder Lubricant - Dry Talc powder lubricant, 8 lb container. Absorbs moisture and keeps treated seed from sticking together in planter boxes. Recommended application rate: 3 oz. Coverage: Typically treats 60-80 acres. (Item #: 107928, Ref: TP19000TP) $22.10

Lights
Headlight Assembly, Teardrop- 12 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 12-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112414, Ref: 45640DB-12V) $43.10
Headlight Assembly, Teardrop - 6 Volt - Original Style, TEAR-DROP shaped back. PAINTED RED. 6-VOLTS. Approx 5" diameter. Price is for one complete headlamp assembly. Original replacement for many IH tractors. Verify your configuration (Teardrop vs. Flat-Back) before ordering. (Item #: 112415, Ref: 45640DB) $42.80
Light Bulb, Sealed Beam, 6 Volt - 4-1/2 inch number 4511. (Item #: 111227, Ref: 373661R91) $13.50
Portable Halogen Work Lamp - 3 inch x 5 inch sealed beam unit, 12 volt, 50 watt, 4 amp. With handle and magnetic base. Projects flood beam pattern 50 foot wide x 30 foot long. Lamp is not legal for street use. (Item #: L200MAGH) $75.13
No Picture Sealed Beam Light - 6 Volt (Item #: 111938, Ref: R2712) $46.30
No Picture Sealed Beam Light - 12 Volt (Item #: 122080, Ref: R2713) $36.00
Switch, Light, with Knob - Universal switch, for 6 volt tractors. Verify style is correct for your model. (Item #: 114720, Ref: AA4667R) $16.60
Work Light 12V - Universal Work light is 12 volt, 3000 candle power, and a trapezoidal light pattern. I does swivel up and down, not side-to-side. Comes with 4-1/2" diameter sealed beam lamp, part number L4411. Does not have a switch on the back. (Item #: 173803, Ref: L408-12V) $38.40

Miscellaneous
Cab Foam Kit - With Headliner 10-Piece - Black For tractor models with QT1 Year Round Cab. Must be truck shipped - $75 will be added for shipping due to weight and size. (Item #: 186987, Ref: R1236) $389.00
Deluxe Canopy, 3 Bow - This universal Blue 3-Bow Deluxe Canopy comes with bows and cover. Universal brackets sold separately. Fender mounting kit is part number 6A216. Axle Mounting Kit is part number 6A217. Measures about 48 inch spread from Mounting brackets (40 inch spread at the top of canopy) Height is approximately 31 inch. (Item #: 178876, Ref: RFC100B) $245.00
Hand Cleaner, Gallon - Hand cleaner, with dispenser pump. 1 gallon plastic bottle. (Item #: 180453, Ref: PRM25218) $24.60
Tractor Umbrella with Frame & Mounting Bracket - Red - Complete umbrella consisting of a cover, bracket and frame, 54" x 54" cover made of 10 oz. duck canvas with leather reinforcements and steel grommets, Metal parts are zinc-coated for long-lasting, maintenance-free service, Rigid framework for cover is built to withstand farm and industrial use, Installs easily, folds down for trailering and removes in seconds without tools, (Item #: 161193) $123.00

Paint
44 Minute DVD - How to Paint a Tractor - This DVD demonstrates the entire painting process including sanding, priming, body work, painting and decals. A John Deere B is used as the sample tractor, but the information will pertain to any make or model - the techniques are the same. Safety is also discussed. (Item #: 183950, Ref: JDV-02250) $24.00
No Picture Paint, Aluminum High Heat Spray Can - 12 oz. spray can. Withstands heat up to 650 degrees for use on stacks and mufflers. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP402HHSP_) $8.50
No Picture Paint, Aluminum, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100244, Ref: TP312SP) $8.50
No Picture Paint, Clear Coat, 1 Gallon - High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108409, Ref: TP447GAL) $65.00
No Picture Paint, Clear Coat, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High strength air dry Acrylic laquer. Protects the original paint finish, adds more shine, prolongs color and prevents fade. Water clear non-yellowing gloss coat, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108408, Ref: TP447QT) $30.00
No Picture Paint, Farmall Red, 1 Gallon - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101108, Ref: TP110GAL) $55.00
No Picture Paint, Farmall Red, 1 Quart - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101107, Ref: TP110QT) $24.60
No Picture Paint, Farmall Red, Spray Can - This "Farmall" Red is for those models that were manufactured under the earlier FARMALL Brand (Not International). From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP110SP) $8.50
No Picture Paint, Gloss Black, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100116, Ref: TP550GAL) $53.00
No Picture Paint, Gloss Black, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100115, Ref: TP550QT) $24.00
No Picture Paint, Gloss Black, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100114, Ref: TP550SP) $8.70
No Picture Paint, Gray Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100121, Ref: TP2700QT) $22.40
No Picture Paint, Gray Primer, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. (Item #: 100120, Ref: TP2700SP) $8.30
No Picture Paint, IH Blue, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101114, Ref: TP910GAL) $58.00
No Picture Paint, IH Blue, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101113, Ref: TP910QT) $24.00
No Picture Paint, IH Blue, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101112, Ref: TP910SP) $8.60
No Picture Paint, IH Red, 1 Gallon - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100722, Ref: TP905GAL) $56.00
No Picture Paint, IH Red, 1 Quart - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100721, Ref: TP905QT) $24.00
No Picture Paint, IH Red, Spray Can - This "IH" Red is for those models that were manufactured under the INTERNATIONAL Brand (Not Farmall). High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100720, Ref: TP905SP) $8.50
No Picture Paint, McCormick Deering Gray, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108401, Ref: TP450GAL) $90.00
No Picture Paint, McCormick Deering Gray, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108400, Ref: TP450QT) $35.00
No Picture Paint, McCormick Deering Gray, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 108399, Ref: TP450SP) $11.00
No Picture Paint, Off White, 1 Gallon - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101117, Ref: TP900GAL) $62.00
No Picture Paint, Off White, 1 Quart - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101116, Ref: TP900QT) $24.90
No Picture Paint, Off White, Spray Can - High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 101115, Ref: TP900SP) $8.20
No Picture Paint, Red Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100119, Ref: TP3987GAL) $59.00
No Picture Paint, Red Primer, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100118, Ref: TP3987QT) $24.00
No Picture Paint, Satin Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP225QT) $24.00
No Picture Paint, Satin Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics.Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP225SP) $8.50
No Picture Paint, Universal Non Glare Black, 1 Quart - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100254, Ref: TP120QT) $24.00
No Picture Paint, Universal, Non Glare Black, Spray Can - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 100253, Ref: TP120SP) $8.50
No Picture Paint, Yellow Primer, 1 Gallon - From Tallmans, formulated by Van Sickle, providing OEM quality. High Strength air dry enamel with Alkyd resins to assure durability. Fade resistant, smooth uniform film characteristics. Paint cannot be shipped to California due to California Regulations. All Paint can only ship UPS Ground. (Item #: 184741, Ref: TP2720GAL) $84.67
No Picture Slip Resistant Coating - Gallon can. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116GAL) $68.39
No Picture Slip Resistant Coating Kit - Do it yourself kit. Comes with one gallon of liner, mini roller with tray, two replacement roller covers, 2" brush, and sanding sponge. For use in a variety of applications where slip resistance or sound deadening qualities are desired. Moisture and chemical resistant, helps protect against corrosion. Ready to use as is for easy application and touch up with brush or roller. Coverage area is 75 to 100 square feet. (Item #: BL116KIT) $99.22
Tire Paint, Black - Black tire paint (1 Gallon)- The best way to make tires look like new. Our paint is a permanent water based paint that applies easily and dries quickly. It will not rub off even when wet. Gives dull, faded tires a non-glossy, like new finish. This paint is READY TO USE. (Item #: 185598, Ref: E844R) $40.01