Yesterday's Tractor Co. Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver

Case VAC - Featured Tractor

The Case VAC model tractor was produced in 1929, 1930, 1931, 1932, 1933, 1934, 1935, 1936, 1937, 1938, 1939, 1940, 1941, 1942, 1943, 1944, 1945, 1946, 1947, 1948, 1949, 1950, 1951, 1952, 1953, 1954, 1955 and 1956 by the J.I. Case company in Racine, Wisconsin. It has a 124 ci engine rated at 28 horsepower.

Our Most Popular Case VAC Parts

(Click here to see all parts available)

Case VAC Cooling System

VAC Fan Belt
Fan Belt - For tractor models V, VA, VAC, VC all without generator; R, RC. Measures about 40.50 inches by 13/16[...] 181636M1 ... $15.53
VAC Water Pump
Water Pump - Less Pulley. Has 2-3/4" impeller diameter. For tractor models 200 gas, 200B 1959 & later, 300, 300B [...] A148401 ... $76.65

Case VAC Decals and Emblems

VAC Decal Set
Decal Set - For the VAC. Give your VAC a new look with this set of 15 self adhesive decals. Includes two Case ea[...] R0763 ... $35.84

Case VAC Electrical System

VAC Distributor Cap, Autolite or Prestolite
Distributor Cap, Autolite or Prestolite - This cap fits Autolite or Prestolite distributors ONLY, with 3-3/8 inch outside diameter, clip held [...] R2009 ... $15.80
VAC Electronic Ignition Conversion Kit, 12V Negative Ground
Electronic Ignition Conversion Kit, 12V Negative Ground - 12 Volt NEGATIVE Ground. (Also available in 12 Volt POSITIVE, 6 Volt NEGATIVE and 6 Volt POSITIVE - [...] 1541 ... $95.95
VAC Electronic Ignition Conversion Kit, High Perfomance, 12 Volt Negative Ground
Electronic Ignition Conversion Kit, High Perfomance, 12 Volt Negative Ground - The Ignitor II has many of the same great features that the Ignitor has, but its smarter. It senses [...] 91541 ... $136.33
Starter Drive - Fits Case V, VA, VAC Replaces OEM# MZ4072, MZ4114[...] 565549 ... $20.93

Case VAC Engine Gaskets

Head Gasket Set - For 124 CID Gas Engine on VA Series: (VA, VAC, VAE, VAH, VAI, VAO, VAS) 1951-1954. (Upper gasket set[...] VGK7519S ... $72.56

Case VAC Exhaust System

VAC Exhaust Elbow
Exhaust Elbow - For tractor models VA, VAC, VAH with Continental Engine. 3 Inch Offset. Replaces OEM# VT200 (To ES #[...] R2659 ... $44.66
VAC Muffler, Vertical
Muffler, Vertical - Inlet I.D. 1-15/16", (C) Outlet O.D. 2", (B) Overall length 29", Shell O.D. 3.25". For (GAS): VA, VA[...] M81C ... $30.78

Case VAC Fuel System / Air Intake

Air Cleaner Cap - Fits Avery A, Case VA, VAC, VAI, VAO & VAH, INDUSTRIALS - 310, 310C, 310D, 310E, 310F, 320, 400B, 42[...] R4801 ... $44.66
VAC Carburetor Float
Carburetor Float - This carburetor float is 2.25 inches wide and is used for the following is used for the following tr[...] CTP28 ... $16.50
VAC Carburetor Kit, Basic
Carburetor Kit, Basic - Kit for Marvel TSX635, TSX937SL, TSX937, TSX957SL, TSX804, TSX680, TSX936SL, TSX936, TSX42, TSX74, T[...] MS101 ... $16.50
VAC Carburetor Kit, Basic
Carburetor Kit, Basic - Kit for Zenith 10136, 7206, 9667, 11506, 11106 carbs used on D, R, RC, S, S80SK, SC, SE, SI, SO, STW[...] Z101 ... $19.50
VAC Carburetor Kit, Basic
Carburetor Kit, Basic - Fits Zenith carburetors 13339, 11532, 13876, 13863, 13714, 12708, 14987, 12825. For tractor models V[...] K2119 ... $24.00
Carburetor Kit, Basic - Kit includes needle and seat, float lever pin, seal, gaskets and instructions. Repairs 61, 68 and 16[...] BK44V ... $26.25
VAC Carburetor, New
Carburetor, New - With reversible linkage. This Zenith carburetor outperforms the original carbs used on: VA series 19[...] 12522 ... $372.60
Carburetor, New - With reversible linkage. This Zenith carburetor outperforms the original carbs used on: S, VA series[...] 14544 ... $418.14
Fuel Cap - Cap also doubles on many models as a radiator cap. For tractor models V, VA, VAC. Replaces G13271. M[...] 760029M91 ... $15.75
Sediment Bowl Assembly - For tractor models D, S, VA, VAC. Sediment Bowl Assembly - Small Bowl. Replaces 03990AB.[...] 910513 ... $17.25

Case VAC Gauges

VAC Oil Pressure Gauge
Oil Pressure Gauge - For tractor models V, VA, VAC, VAC-11, VAC-12, VAC-13, VAC-14, VAH, VAI, VAIW, VAIW-3, VAO, VAO-15, [...] VT2249 ... $22.04
VAC Water Temperature Gauge
Water Temperature Gauge - This water temperature gauge comes with a 60 inch lead for models DC, SC, VAC. Water Temp Gauge with[...] VT2265 ... $29.01

Case VAC Lights

VAC Light Switch
Light Switch - light switch with cut out on generator for tractor models VA, VAC, VAH, VAI, VAO. Replaces VTA463[...] 70208197 ... $29.40

Case VAC Seats

Seat Spring - This Seat Spring is used on VAC when equipped with optional easy ride seat. It Replaces original par[...] 1K1854A ... $37.50

Case VAC Steering

VAC Steering Wheel
Steering Wheel - 16 inch diameter, 7/8 inch-1 inch tapered keyed hub, 3 steel spokes. For tractor models V, VC, VI, V[...] VT2230 ... $40.56

Click here to see our full catalog of Case VAC Parts



Recent Topics

  • New to me VAC - Hello, Im new to posting here, but have read many posts on this website. I just thought you all might be interested in the new toy I just picked up. Im planning to change engine oil in the near future and other basic maintenance, but is there any thing else I need to maintenance. Change transmission oil or just check and top off ect. Thanks
  • Reluctant VAC Work - I have been wanting to do this for awhile but have been dreading it. The tractor wobbles badly in the rear when driving in 4th down the road and really bothers me and looks like poo in the process. When I restored the VAC I was either too lazy, too cheap, or both and did not put new carriage bolts in the axle clamps on the wheel hubs. Because of this I believe I did not get a good and even clamp on the axle shafts on both wheels. So, I need to remove the outside wheel weights, tires/rims, wheel ...
  • VAC Governor - after assembling the 9 ball bearing type governor on my VAC and connecting all throttle linkage, i cannot get any movement out of the governor. it went in with out any problems that i know of. all linkage is free a clear of any obstructoin, so it tells me there is something going on inside the governor. what should i check? it's not running/complete as of yet, i just noticed this when i connect the throttle spring to the governor.
  • VAC Splitting Logs - Got the VAC and log splitter out today to try splitting some logs. The splitter is a Danuser and is being driven off the engine driven pump on the VAC. I set my remote lever into the detent forward position and this allowed me to use the splitter control. The relief valve on the VAC will trip when trying to split anything other than dry wood and anything with a knot in it. I am curious how the belt pulley driven pump would perform in this role compared to the engine driven pump. It would obvious ...
  • dumb vac question - Since I am doing the rear seals on my VAC I have the option of moving the weights if I want to. They are on the outside now. Did Case have a mounting preference. There won't be any putting them on taking them off going on so inside mounts would work. I do use the tractor for garden work. TO me it looks like the weights obstruct the view of some pretty cast wheels.


  • Archived Ads for Case VAC Tractors
    (Information only, no longer for sale)


    Case VA VAC tractor owners operators manual. This is a genuine old original Case manual. Iyt came out of a closed down Case dealership. Can ship ... US shipping about 3 Condition: very nice , Price: 50, Posted 2017-05-12 in Madsion WI.

    Case Vac 14 with Woods 48 inch finish mower. New tires all around, 3 point, wheel weights, less than 100 hours on engine rebuild, all gauges work, manuals Condition: Great Runner, Price: 2500, Posted 2017-07-09 in Kaukauna WI.

    Case VAC fenders; VAC wheel weights; VA nice vintage original operators manual. 50 each item. The manual i will ship to you .. fenders weights pickup here thanks Condition: good vintage originalls, Price: 50, Posted 2017-07-15 in WI.

    Case VAC wide front. Row crop adjustable style. Condition: Good, Price: 300, Posted 2017-07-28 in Bridgewater VA.

    1918 F fordson, 1950 Farmall cub lo-boy.1953 VAC case, 1948 Leader, 1949 Allis- Chalmers G, Harris pony restored w/ cultivators like new. 84 yrs. old selling tractors I cant finish. Priced as calls com in . All tractors are complete NO PARTS TO FIND Condition: Poor to new restored, Price: 1000-7000, Posted 2017-08-08 in waynesville NC.

    Important: Yesterday's Tractor Co. takes no responsibility for the accuracy, validity or availability of the items listed here nor do they receive any profit from the 3rd party transactions that may transpire from the use of this website. Yesterday's Tractor Co. does not sell tractors, nor do we collect money or broker transactions for others.




    TRACTOR PARTS TRACTOR MANUALS
    Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

    Home  |  Forums


    Copyright © 1997-2018 Yesterday's Tractor Co.

    All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

    TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

    Yesterday's Tractors - Antique Tractor Headquarters

    Website Accessibility Policy